User manual MINOLTA CA-210 BROCHURE

[. . . ] (Requires expansion board CA-B14) · USB connection provided as standard, so it can be connected even to computers without serial ports. ACCURATE · Accuracy of ±0. 002 for White, ±0. 004 for R, G, B. (Chromaticity) · CIE 1931 Standard Observer XYZ Filter. · Matrix measurement enables high accuracy for not just white, but for monochrome colors as well. LOW LUMINANCE · Precise measurement can be obtained at low luminance, enabling lower luminance and highaccuracy contrast measurement. [. . . ] By using a special optical system in the CA-210, the angle of the received light is symmetrical about the normal to the emitting surface for every point within the measuring area (27 mm). Since the viewing angle of the CA-210 is 5°, the light received would be only the light within ±2. 5° relative to the normal to the emitting surface (shown as a dotted line in the figure). Measurement position and incident angle of conventional instrument '1 1 2 3 '3 Measurement position and incident angle of CA-210 1 2 3 System Diagram Muli-Probe (Optional) 4-Probe Expansion Board CA-B14 (Optional) PC (Commercially available) PC-AT compatible Universal Measuring Probe CA-PU12 (2 m) CA-PU15 (5 m) Small Universal Measuring Probe CA-PSU12 (2 m) CA-PSU15 (5 m) LCD Flicker Measuring Probe CA-P12 (2 m) CA-P15 (5 m) Small LCD Flicker Measuring Probe CA-PS12 (2 m) CA-PS15 (5 m) (Hood and Lens Cap included) Standard Hood for CA-210 CA-H10(Standard) or Small Hood for CA-210 CA-HS10(Standard) CA-210 PC Software for Color Analyzer CA-SDK(Standard) Select the probe among the following four types. Universal Measuring Probe CA-PU12 (2 m) CA-PU15 (5 m) Small Universal Measuring Probe Standard Lens Cap for CA-210 CA-PSU12 (2 m) CA-H11(Standard) CA-PSU15 (5 m) or LCD Flicker Measuring Probe CA-P12 (2 m) Small Lens Cap for CA-210 CA-P15 (5 m) CA-HS11(Standard) Small LCD Flicker Measuring Probe CA-PS12 (2 m) CA-PS15 (5 m) AC Power Cord (Standard) LCD Flicker Measuring Probe is applied to the "Flicker measuring function". Because of this it is not able to measure the display whose emission intensity fluctuates in single frame scanning period. DISPLAY COLOR ANALYZER CA-210 LCD Flicker Measuring Probe Small LCD Flicker Measuring Probe Same model as CA-210 measuring probes sold until May 2003. Select the probe among the following four types. LCD Flicker Measuring Probe LCD Flicker Measuring Probe (Measurement area 27 mm / Cable length: 2 m) (Measurement area 27 mm / Cable length: 5 m) (Measurement area 10 mm / Cable length: 2 m) (Measurement area 10 mm / Cable length: 5 m) CA-P12 CA-P15 Small LCD Flicker Measuring Probe CA-PS12 Small LCD Flicker Measuring Probe CA-PS15 Up to five probes can be connected to a single main body. Universal Measuring Probes, Small Universal Measuring Probes, LCD Flicker Measuring Probes and Small LCD Flicker Measuring Probes can be connected simultaneously to a single main body. (To connect multiple probes, the optional four-point extension board (CA-B14) is necessary. ) CRT COLOR ANALYZER Select the probe among the following four types. CA-100Plus Measuring Probe High luminance Measuring Probe Please request a CA-100Plus catalog for further information. Measuring Probe Measuring Probe (Cable length: 5 m) (Cable length: 2 m) CA-P02 CA-P05 CA-PH02 CA-PH05 High luminance Measuring Probe (Cable length: 2 m) (Cable length: 5 m) High luminance Measuring Probe Up to five probes can be connected to a single main body. Measuring Probes and High luminance Measuring Probes can be connected simultaneously to a single main body. (To connect multiple probes, the optional four-point extension board (CA-B04) is necessary. ) Applicability of CA series for different display types This table is based on the most popular method for controlling emission intensity for each display type. (1) Measurements of displays using certain control methods are not possible. For details of measurement compatibility, contact your nearest Minolta representative. Examples for which measurement is not possible: · Displays which use PWM, etc. · Displays with backlights which emit intermittently. · Displays which write black for each frame, etc. [. . . ] (Three-digit indication can be chosen. ) Flicker (Contrast method) 3 xyLv, R/G B/G G, R B/R G/R xyLv, R/G B/G G, R B/R G/R, Flicker (Contrast method) 3 Analog 16 characters by 2 lines (with backlight) LCD NTSC, PAL, EXT, UNIV, INT SYNC mode Vertical synchronization frequency: 40 to 200 Hz (Luminance or chromaticity measurement), 40 to 130 Hz (Flicker measurement) Vertical synchronizing frequency: 40 to 200 Hz Object under measurement 100 channels Memory channel Standard function Analyzer function RS-232C (38, 400 bps or below), USB (Rev. 1. 1) Interface Max. 5 points(Use 4-Probe Expansion Board CA-B14) Multi-point Measurement SDK software (supplied as standard accessory) Software Operating temperature/humidity range Temperature : 10 to 28°C; relative humidity 70 % or less with no condensation Luminance change : ±2 % ±1 digit of reading for white Chromaticity change ±0. 002 for white, ±0. 006 for monochrome from reading of Konica Minolta's standard LCD1, 160. 0 cd/m2, with 23°C 40 % Storage temperature/humidity range 0 to 28°C : relative humidity 70 % or less with no condensation 28 to 40°C : relative humidity 40 % or less with no condensation 100 ­ 240 V~, 50­60 Hz, 50 VA Input voltage range Main body: 340 (W) × 127 (H) × 216 (D) mm, Main body: 340 (W) × 127 (H) × 216 (D) mm, Main body: 340 (W) × 127 (H) × 216 (D) mm, Main body: 340 (W) × 127 (H) × 216 (D) mm, Size Probe: 49 × 204 mm Probe: 49 × 232 mm Probe: 49 × 204 mm Probe: 49 × 232 mm Main body: 3. 58 kg, Probe: 520 g Weight Main body: 3. 58 kg, Probe: 540 g Main body: 3. 58 kg, Probe: 520 g Main body: 3. 58 kg, Probe: 540 g 1 : The chromaticity and luminance are measured under Konica Minolta's condition (standard LCD(6500 K, 9300 K) is used). · Specifications are subject to change without notice. [. . . ]