User manual MINOLTA MAGICOLOR 2 PLUS

[. . . ] ® ®  The following are trademarks or registered trademarks of their respective owners. Other product names mentioned in this manual may also be trademarks or registered trademarks of their respective owners. Registered trademarks are registered in the United States Patent and Trademark Office; some trademarks may also be registered in other countries. QMS, Crown, CrownAdmin, CrownNet, magicolor, the QMS logo, and the Crown seal are registered trademarks of QMS, Inc. , and CrownView, ImageServer, PS Executive Series, QCOLOR, and QFORM are trademarks of QMS, Inc. [. . . ] If you have the duplex model, the duplex unit paper guides After. . . Every 20, 000 single-sided pages, or 12 months, whichever comes earlier. User See information about cleaning the duplexer on page 6-8. User See information about cleaning the duplexer on page 6-8. If you have the duplex model, the duplex unit roller Every 20, 000 single-sided pages, or 12 months, whichever comes earlier. Laser lens Only when you find vertical white or User light-colored streaking in all See "Cleaning the Laser primary colors on your printouts. Every 20, 000 single-sided pages, or 12 months, whichever comes earlier. Every 20, 000 single-sided pages, or 12 months, whichever comes earlier. Every 20, 000 single-sided pages, or 12 months, whichever comes earlier. As needed User See "Cleaning the OPC Belt Cartridge" on page 6-10. User See "Cleaning the Transfer Unit" on page 6-4. User See "Cleaning the Paper Exit Rollers" on page 6-9. User See "Cleaning the Exterior of The Printer" on page 6-19. OPC belt cartridge and corona wire (also known as the OPC charge wire) Paper discharger Paper exit rollers (also known as paper guides) Printer exterior   #) This item needs cleaning. . . Every 20, 000 single-sided pages, or 12 months, whichever comes earlier. By. . . User See "Guidelines for Cleaning Inside the Printer" on page 6-3. User See "Cleaning the Transfer Unit" on page 6-4. User See "Cleaning the Transfer Unit" on page 6-4. Registration roller Every 20, 000 single-sided pages, or 12 months, whichever comes earlier. Every 20, 000 single-sided pages, or 12 months, whichever comes earlier. Transfer roller  This item needs preventive maintenance. . . Printer--20, 000-page preventive maintenance After. . . By. . . 20, 000 single-sided pages. User See the standard "Cleaning Schedule" on page 6-20. Printer--60, 000-page preventive maintenance Printer--120, 000-page preventive maintenance 60, 000 single-sided pages. QMS National Service or a QMS-authorized service provider QMS National Service or a QMS-authorized service provider Replace 120K kit displays in the message window (after 120, 000 single-sided pages). %  (  #) This item needs replacing. . . Check fuser cleaning rol[l]er or Replace cleaning Roller displays in the message window (after 12, 000 single-sided pages at 5% coverage of each color). User See "Replacing the Fuser Oil Bottle and Cleaning Roller" on page 6-24. Fuser cleaning roller User See "Replacing the Fuser Oil Bottle and Cleaning Roller" on page 6-24. Fuser oil bottle Check fuser oil & cleaning rol[l]er displays in the message window (after approximately 12, 000 single-sided pages; however, fuser oil bottle life is media dependent--coarser paper requires more oil). User See "Replacing the Fuser Oil Bottle and Cleaning Roller" on page 6-24. OPC belt cartridge (with charger unit) Replace OPC displays in the User message window (maximum See "Replacing the OPC Belt life--50, 000 planes, usually Cartridge" on page 6-28. occurs with continuous use; minimum life--20, 000 planes, usually occurs with intermittent use although other factors also affect cartridge life). 60, 000 planes or every 12 months, whichever comes earlier. [. . . ] You will switch this printer cover plate with the one from the lower input feeder after the cables have been disconnected. 3 Locate the cable at the left rear of the input feeder, and disconnect it. 4 Reinsert the two cover plates. Put the one originally on the input feeder on the printer, and put the one originally on the printer on the input feeder. 5> #%  ( 529#3" 7 5 Unscrew the thumbscrews that attach the two brackets (one on each side of the printer) to the lower input feeder.  6 Remove the two metal brackets from underneath the sides of the printer. Angle the bracket out, and then, slide it out of the hole underneath the printer. 40 , '  7 Place tape on the printer as shown in the illustration. (  529#3" 7 WARNING!Your printer weighs approximately 66 lbs (30 kg) without consumables. [. . . ]