User manual MINOLTA MAXXUM 3XI PART 1

[. . . ] · Do not subject the camera to shock, extreme heat or high humidity. · Do not let the camera come in contact with sand, salt, or other grit. · This camera is designed for use between -10 and 40 °C (14 to 104 F). · At colder temperatures, the data panel response time may be slow. [. . . ] · When not in use, keep the camera in a cool, dry place away from dust and chemicals. For extended storage, place the camera in an airtight container with a drying agent such as silica gel. · For more information about your camera, contact your local camera dealer or the Minolta distributor in your area. FOR PROPER AND SAFE USE Read and understand all warnings and cautions before using this product. WARNING Batteries may become hot or explode due to improper use. · · · · · Use only the batteries specified in this instruction manual. Do not install the batteries with the polarity (+/­) reversed. Do not subject batteries to fire or high temperatures. Do not attempt to recharge, short, or disassemble. Follow local codes for battery disposal. Tape over lithium battery contacts before disposal. Use caution, accidents may occur when using this product near young children. Keep batteries or things that could be swallowed away from young children. Contact a doctor immediately if an object is swallowed. Immediately remove the batteries and discontinue use if. . . · the camera is dropped or subjected to an impact in which the interior is exposed. ADJUST button ** Remote-control models only. Back cover * Do not touch. IMPRINTING THE DATE AND TIME 1 Press the MODE button to choose the data imprinting format. · The display will change as shown. · When -- -- -- is displayed in the data panel, no data will be printed on the print. SETTING THE TIME AND DATE 1 Use the SELECT button to move between different parts of the displayed data. The selected part will blink indicating that it is the data to be changed. 1. Cartridge mark DATA PANEL 2 Press the ADJUST button to change the data to the correct value. Data continues changing as long as you hold down the button. · In Time mode, pressing the ADJUST button while the colon is blinking resets the second counter to 00. VIEWFINDER 1. Flash lamp (green) Glows: Flash is ready Blinks: Flash charging 3 When all data is correct, press the SELECT button until the data stops blinking. · Reset the time and date after changing the battery. Step ATTACHING THE STRAP Attach the strap as shown. This mark on your camera certifies that this camera meets the requirements of the EU (European Union) concerning interference causing equipment regulations. CE stands for Conformité Européenne (European Conformity). Step INSERTING THE BATTERY Your camera uses one 3-volt CR123A or DL123A lithium battery to supply power for all camera operations. 1 Open the battery-chamber door using a coin or similar object. 2 Insert the battery ­ side first as shown, then snap the battery-chamber door closed. · Before opening the battery-chamber door, make sure the camera is off. · Remove batteries + side first. Step TAKING PICTURES 1 Press the Main switch to turn the camera on. 2 Align your subject within the focus frame and press the W side of the zoom lever to move toward wide angle or the T side to move toward telephoto. · Your subject must be at least 1m (3. 3 ft. ) away from the lens in Wide and 1. 1m (3. 6 ft. ) away in Telephoto. [. . . ] Press the main switch to restore power. · Do not obstruct the lens while it is retracting. FOCUS HOLD When your subject is located outside the focus frame, you can first lock focus on your subject, then recompose the picture as desired. Step 1 Align the subject within the focus frame and press the shutter-release button partway down. LOADING THE FILM Use only 35mm, negative film rated ISO 100, 200, or 400. Non DX-coded film is set to ISO 100. · Do not use Polaroid instant 35mm film. Winding problems may occur. 2 Without lifting your finger, recompose the picture then press the shutter-release button all the way down to take the picture. · Lift your finger from the shutter-release button to cancel focus hold. 1 Slide the back-cover release down to open the back cover and place the film cartridge into the film chamber. · Always load and unload the film in subdued light. Step REWINDING THE FILM The film will rewind automatically after the last frame has been exposed. When appears and blinks in the data panel, open the back cover and remove the film. 2 Extend the film tip to the "FILM TIP" mark, making sure it lays flat. · If the film tip extends past the mark, gently push the excess film back into the film cartridge. If rewind stops before the film has been completely rewound, all indicators blink. [. . . ]