User manual MINOLTA RD-175

[. . . ] Other trade names and product names are also registered trademarks. 2 RD-175 Digital Camera USER LICENCE AGREEMENTS Please read through the terms below carefully before you use the enclosed product. By using the product, you will have agreed to be bound by the terms of this agreement. Should you not agree with the terms, please return the unopened package immediately. This agreement is a licence agreement and not a purchase contract. [. . . ] If the master switch was already set to ON, slide it back to LOCK, wait 30 seconds and then slide it back to ON. Kamera3. bmp You will see "SCSI" at the bottom right on the display. The SCSI ID is shown at the top on the display. Keeping the MODE key pressed, press the Program-Select key (P) Kamera4. bmp The terminator power supply is shown on the display Release the MODE key. Power is now supplied to the terminator via the internal battery. Please follow precisely the same procedure in order to switch the power supply back to your PC. 11 RD-175 Digital Camera 3. 3 Inserting the PC card Slide the PC card into the card slot as specified in the instructions on Page 27 of the User Manual for the RD-175 Digital Camera. 12 RD-175 Digital Camera 4. Preparing the PC Install MS-DOS, Windows and the TWAIN-compliant image-editing software (e. g. Adobe Photoshop, Corel Photopaint etc. ) on your computer. We recommend Adaptec SCSI controllers of Series 1520/1522 or 1540/1542. ISA-bus computers do not support more than 16 MB RAM. Should you be using an Adaptec ISA controller of Series 1540/1542 with the RD-175 Digital Camera, please ensure that the amount of RAM installed is not greater than 16 MB since your system would otherwise not work correctly. Please make the following settings for the SCSI host adapter, depending on the SCSI ID which you have selected for connecting the camera, before you connect the RD-175 Digital Camera to your computer: "Initial Sync Negotiation" - OFF "Enable Disconnection" - OFF Please consult the Manual for the SCSI controller if necessary in order to make these settings. If there are more images stored on the PC card, you can scroll to them by clicking on the scroll arrows. 17 RD-175 Digital Camera 6. 3 Saving displayed images on your PC's hard disk Click on the required image - it will then be displayed with a border. The related aperture setting (F No. ) and shutter speed (SS) in addition to the date and time of the recording are displayed in the lower area of the window. rd175_4. bmp Choose "Load". Mark the image which you wish to delete by clicking on it. If you wish to delete several images, keep the Shift key pressed when marking. Click on the "Select All" button in order to delete all images. The selected images are then displayed with a border. Click on the "Delete. . . " button. You will now see the following dialogue box. rd175_10. bmp Choose "Yes" if you wish to delete the images. Choose "No" if you wish to abort the delete operation. If the operation is quit or aborted, you will see the main menu window again. 22 RD-175 Digital Camera 6. 7 Deleting images from the PC card You may delete individual images, several images or all images from the PC card with the aid of TWAIN module. It is not possible to recover deleted images. [. . . ] If you use PC cards which are not standard accessories, please ask your MINOLTA dealer for details. Remove the PC card and insert the PC card to be initialised (you will see "Er" for error on the camera display if the PC card is not yet formatted). You will see the following message if the PC card has not yet been initialised by the RD-175: rd175_15. bmp Click on "OK". The blank main menu window is now opened. rd175_16. bmp 27 RD-175 Digital Camera Click on the "Camera etc. . . . " button Click on the "Initialise" button next to "Format HDD Card" in the top third of the "RD-175 Control" window. rd175_12. bmp You will see the following warning before initialisation commences: rd175_17. bmp If you really do wish to initialise the PC card, please choose "Yes". [. . . ]