User manual MINOLTA XE-5 IR REMOTE CONTRO LRC-3

[. . . ] Box 6000, NL-3600 HA Maarssen, The Netherlands Prins Boundewijnlaan 1, B-2550 Kontich, Belgium Riedstrasse 6, CH-8953 Dietikon, Switzerland Albygatan 114, S-171 54 Solna, Sweden Niittykatu 6 PL 37, SF-02201 Espoo, Finland Av. do Brasil 33-A, P-1700 Lisboa, Portugal 101 Williams Drive, Ramsey, New Jersey 07446, U. S. A. 11150 Hope Street Cypress, CA 90630, U. S. A. 369 Britannia Road East, Mississauga, Ontario L4Z 2H5, Canada 230-3771 Jacombs Road, Richmond, B. C. [. . . ] The viewfinder changes to match your selection. INSERTING THE BATTERY Your camera uses one 3-volt CR2 lithium battery to supply power for all camera operations. Hold the camera steady, making sure your fingers do not cover the flash. If you are taking a vertically framed picture, turn the camera so the flash is on top. 1. Open the battery-chamber door using a coin or similar object. Insert the battery according to the + and ­ marks inside the battery chamber then snap the cover closed. · Reset the date and time after installing a new battery. 3. Looking through the viewfinder, frame the subject as desired. Push the zoom lever toward W to zoom out. Push the zoom lever toward T to zoom in. · Do not obstruct the lens barrel. 4. Center your subject in the focus frame, then press the shutter-release button partway down. CHECKING THE BATTERY POWER Each time the camera is turned on, a symbol will appear briefly in the data panel to indicate the power status of the battery. Power is sufficient for all camera operations. 5. When the green ready lamp glows, press the shutter-release button all-the-way down to take the picture. · Press the shutter-release button with a slow, steady squeeze, never a quick jab. Power is sufficient, but the battery will have to be replaced soon. 6. Turn the camera off after use by sliding the front cover closed. Replace the battery. The shutter will lock until the battery is replaced. · If no display appears, replace the battery or check that it is inserted correctly. Auto Power Off : To save power, your camera will shut down and retract the lens if it is not operated for more than eight minutes. Close, then open the front cover again to restore power. FOCUS HOLD If your subject is located outside the focus frame, you can first lock focus on your subject, then recompose the picture as desired. 1. Align the subject within the focus frame and press the shutter-release button partway down until the ready lamp glows. LOADING THE FILM Your camera uses IX240 type film designed for use in Advanced Photo System cameras. · The automatic transport system loads the film, sets the film speed, and advances the film after each exposure. · After loading, the film chamber cannot be opened until rewind has been initiated. ISO 400 0. 5 - 8. 8m 1. 64 - 28. 86 ft 0. 5 - 3. 6m 1. 64 - 11. 80 ft. 1. Place the camera on a tripod and press the self-timer button until appears in the data panel. 2. Center your subject in the focus frame, then press the shutter-release button all the way down to activate the self-timer. SELECTING THE FLASH MODE The following flash modes can be selected. Autoflash Autoflash with red-eye reduction Manual fill-flash Flash cancel Night portrait Landscape Press the flash-mode button until the desired indicator appears in the data panel. · The flash mode remains after the picture is taken. · The self-timer indicator in the data panel and the self-timer lamp blinks during the countdown, then glows just before the shutter releases. · Self-timer is automatically cancelled after the shutter is released. · To stop the self-timer, press the self-timer button. 3. Lift your finger from the shutter-release button, then recompose the picture. 4. Point the remote toward the front of the camera and press or . · The focus remains locked until the focus is reset, remote-control mode is cancelled, or the camera is turned off. Press the flash-mode button until data panel, then take the picture. appears in the · When the flash is cancelled, shutter speeds may be slow. Placing your camera on a tripod is recommended. NIGHT PORTRAIT MODE In night portrait mode, the camera balances the flash and existing light exposure so you can take beautiful pictures of people at sunset or at night. The flash is set to manual fill flash with red-eye reduction. CHANGING THE BATTERY The remote-control uses a 3V lithium battery CR2032. [. . . ] PRESELECTING TITLES Two title codes have been set into memory. You can change one or both title codes at any time. SETTING THE DATE AND TIME 1. Close the front cover to turn the camera off. 1. Close the front cover to turn the camera off. 2. Select the code for the title you want from the title list sheet. 3. Press the title button to display the title code you want to change. 2. Press the date button to display the date. 4. Press the select button, the last digit of the title code number will blink. [. . . ]