User manual MINOURA E-HYPERRIM ALU-LW

[. . . ] Accidents may occur from cracked or damaged couplings. A) You should not tighten the wheel axle by tightening the left side knob. This is for pre-adjusting the wheel position to the exactly center of the drive roller only. Securley tightening your bike to the trainer should be done with the right side hub handle only. [. . . ] G) ! 7 Adjust the wheel position by checking the double-circle position indicators on both side. The best position should be each indicator can be seen equally, but if your rim is narrow, you should adjust the wheel position to be a little left (toward Mag side) to prevent unexpected slippage problem. NOTE: Be sure that the left knob is NOT for tightening the axle. Clamping wheel securely must be done by the right side hub handle. (Fig. H) USING THE PLATIC SKEWER NUT PROTECTOR We recommend you should replace your wheel axle to the supplied quick release skewer to avoid any fitting problem that may occur during workout, because our coupling is designed to fit to the supplied skewer only. Hole (Fig. I) The right side coupling has a black plastic skewer nut protector (called a "Grommet"). This is to protect your skewer from damage during use. Minoura cannot guarantee compatibility with all makes and models of skewer, however when using your own skewer please use the supplied grommet. We will NOT guarantee any fitting problem or accident caused by using your own skewer on the trainer. When you use the supplied skewer, you should remove the grommet from the coupling. It can be done by inserting a rod or a pen to the hole (see Fig. I) and lift up the grommet. -5- HOW TO INSTALL THE REMOTE LEVER You can install the remote lever on anywhere the diameter is between 22. 2mm (7/8") and 31. 8mm (1-1/4") like as on the handlebar. 1 2 Fully loosen the knob bolt on the plastic holder until it stops then push down the bolt to open the holder. J) Place the holder onto the handlebar, shut the holder, and pull up the bolt then tighten it. K-2) Depends on the diameter of your handlebar, you must adjust the shim as follows; · 22. 2mm (7/8") - 25. 4mm (1"): Install both shims. · 28. 6mm (1-1/8"): Install either right or left side shim. · 31. 8mm (1-1/4"): Remove both shims. USING THE MAG RESISTANCE UNIT ! When you install the shim on the plastic holder, make sure the direction of the shim as shown in Fig. J-2. The Mag unit has 7 different levels of load force, replicating actual riding resistance. The load settings range from high (H) to low (L) can be adjusted via the white lever on the Magturbo unit or the lever on the thumb shifter type remote lever device. You may also adjust the load force by shifting up or down among your gears, depending on the level desired. We recommend that you start with a medium to low load force and gradually work up, increasing force as your muscles warm up. Increasing Load Force To increase the load force, move the white lever on the Mag unit toward the (H) symbol. L) If your Mag unit is a remote control type, turn the lever on your thumb shifter device toward the (H) symbol. N) Decreasing Load Force To decrease the load force, move the white lever on Mag unit toward the (L) symbol. M) Be sure the lowest selection is not zero load, there still be a small level of force. [. . . ] The instructions manual will come with the replacement V-belt kit, also you can download it from our web site (http://www. minoura. jp). -7- CHANGING TO REMOTE TYPE You can change your dial type Mag unit to be a remote controlable one. Of course, the opposite way is possible. 1 Remove the dial lever by removing two small screws. Spring Position for Remote type 2 Remove the bottom spring holder by removing two medium screws and remove the inside spring. You should keep a memo where the bottom pin of the spring was installed for returning to dial type again. Change the spring position as shown in the Fig. [. . . ]