User manual MINOURA P-500AL-2

[. . . ] The distributor can be found on our web site. Only when you cannot get enough service, you can contact us. MINOURA North America (for U. S. residents only) 1996 East Avenue, Hayward, CA 94541 U. S. A. Phone 1-510-538-8599 Fax Mail 1-510-538-5899 support@minourausa. com MINOURA Japan Headquarters (for ALL worldwide customers) 1197-1 Godo, Anpachi, Gifu 503-2305 Japan Fax Mail Web +81-(0)584-27-7505 minoura@minoura. jp www. minoura. jp MADE IN JAPAN -1- How To Setup Your P-500AL-2 Required Tools: 1 x 5mm Hex Wrench (included) 1 x 10mm Spanner 1 x 13mm Spanner Cradle Bar Top Frame Cradle Hook Bolt Variation A) Cradle Support Main Pillar Type-A (plain type) Type-B (w/ spring washer) Type-C (w/ flat & spring washers) Front Leg (L) C) Alloy Bar & Cradle Hook B) Angle Adjust Plate (projection is foreside) Support Bar Rear Leg Completed Bike Cradle (order is C, B and A from foreside) Foot Adjuster Base Plate Front Leg (R) <Fig. [. . . ] E) Main Pillar M6x18 Bolt (B) Bolts (type-B) into the holes temporarily to hold the Main Pillar. Raise up both Support Bars. Insert the Plastic Shim between the Support Bar and the Main Pillar, then tighten them with the Tighten two bolts in Step-4 firmly. M6x70 Bolt (type-A), M6 Flat Washer and Nylon Nut (see Fig. F). Flat Washer M6x70 Bolt (A) <Fig. E> Plastic Shim Flat Washer Nylon Nut Support Bar ! Be sure the Support Bars are on the INSIDE of each Front Leg. 6 7 8 Attach the Cradle Hooks from behind of the Alloy Bar then screw the bolts from the front side. The hook distance will be adjusted later to fit the actual bike frame size. F> Place the Alloy Bar onto the Angle Adjust Plate, then screw to the upper hole on the Cradle Support with the M6x20 (type-A) bolt. After that, screw the M6x14 (type-C) bolt to the lower hole. G> M6x20 Bolt (A) Install each Bike Cradle to the Main Pillar. To install the Stainless Band Clip, follow the steps below; 1) Once disassemble the Stainless Band Clip. 2) Open the band and wind it around the Main Pillar. Arch side M6x14 Bolt (C) <Fig. H> Stainless Band (45mm) Plastic Bracket Flat Washer 3) Lap the band ends (see Fig. The end with a welded nut not, adjust the bending angle. Make sure that both ends fit each other. I> 4) Attach the Plastic Bracket onto the band. It should be 5) Put the bolt into the hole on the hook, then screw into the 6) Adjust the hook position and tighten the bolt firmly. J> ! If the inside band end with welded nut has been angled against the bolt, you won't be able to screw the bolt in. Make sure the nut side end is properly set at right angle to the bolt. K) Do not push the bolt so much when screwing in. The band end will have to be bent and you are no longer tighten the bolt. Bottom Arch 90º <Fig. K> Stainless Band must be located in upper position ! Bottom Arch must be located in lower position <Fig. L> -3- 9 Assemble the upper Bike Cradle for the Top Frame. [. . . ] Using the Foot Adjusters, make sure all feet are contacting the (see Fig. Then tighten the Lock Nut using a 13mm spanner. 13 Place your bike on the Bike Cradle using both hooks supporting greater stability. The hook distance should be as wide as possible for !! If your bike has a heavily sloping top tube, change to hook the juncture of the seat tube and seat stay to set your bike more stable. [. . . ]