User manual MITEL 5324

[. . . ] MITEL 5312/5324 IP Phones SIP User and Administrator Guide Release 7. 2 5312 and 5324 IP Phone SIP User and Administrator Guide NOTICE The information contained in this document is believed to be accurate in all respects but is not warranted by Mitel NetworksTM Corporation (MITEL®). The information is subject to change without notice and should not be construed in any way as a commitment by Mitel or any of its affiliates or subsidiaries. Mitel and its affiliates and subsidiaries assume no responsibility for any errors or omissions in this document. Revisions of this document or new editions of it may be issued to incorporate such changes. [. . . ] The log is dialed and the phone returns to the default display. Lift the handset (optional). Redial 1. The last number you dialed appears in the display. Do one of the following: Press the right-hand softkey to dial this number (5324 only). (REDIAL) to scroll the list of previously-dialed numbers and then press Press the right-hand softkey to dial when the desired number is displayed. Note: The redial list is maintained even after the phone reboots and is updated periodically. If a power failure occurs during the update, it is possible that one or more previouslydialed numbers may be lost. Using Speed Dial Keys You may use Speed Dial Keys to make a call or to send a string of digits during a call (press a Speed Dial Key during a call to send a multi­digit password, for instance). Press a Speed Dial key. - 17 - 5312 and 5324 IP Phone SIP User and Administrator Guide Note: If the number you are calling requires an intermediate Long Distance Carrier number to be dialed before the phone number, you can program a Speed Dial number for the Carrier. After pressing the Speed Dial number for the carrier, wait for connection to the Carrier. When connected, press the Speed Dial number for the party you are calling to send the DTMF (touchtone signals) to the Carrier. Note: If the Speed Dial number you want to program requires pauses (for example, if you normally dial a main number, wait for a prompt, and then dial an extension) you can program them into a Speed Dial key by entering a comma to represent a one-second pause. For example, to dial main number 592-2122 and then enter extension 111 after a 3-second pause, program a Speed Dial number as follows: 5922122, , , 111 Answering Calls Incoming calls ring Line 1, if all lines are free, or the next available line. If all lines are busy and Call Forward ­ Busy is not enabled (see Enable/Disable Call Forward on page 21), callers hear a busy signal. When the phone rings, the Ring/Message Indicator and the associated Line key flash, and the name of the caller appears in the information area. Answer a Call To answer a call, do one of the following: · For handset mode, lift the handset. · For headset mode, press the Headset key, then press the flashing Line key. · For handsfree mode, press (SPEAKER) or press the flashing Line key. For more information on handset, handsfree (Speaker) or headset calls, see Handset, Handsfree and Headset Modes on page 27. Auto Answer You can use Auto Answer to automatically answer incoming calls in handsfree or headset mode. To enable or disable Auto Answer: · Access the Feature Configuration page of the Web Configuration (see Accessing the Web Configuration Tool on page 7). To answer an Auto Answer call: · Begin speaking when the call arrives. To end an Auto Answer call, do one of the following: (CANCEL). · Press · Wait for the caller to hang up. - 18 - Making and Answering Calls Answer a Call Waiting The 5324 IP Phone allows a maximum of three calls waiting while you are on a call. The 5312 IP Phone allows one call waiting. When a new call arrives, you hear a call waiting tone, the name of the new caller appears, and the corresponding Line key flashes. [. . . ] At the end of a normal installation, the sectors are restored without affecting SIP Main. However, if power is removed during Boot installation, then SIP Main is erased and will have to be reinstalled on the phone. Automating Firmware Upgrades You can configure phones to poll the server for new versions of firmware. When the phone detects a firmware upgrade, it downloads the new version and stores it in memory. When it is next idle, the phone reboots with the new firmware. [. . . ]