User manual MITSUBISHI CP-D707DW

[. . . ] DIGITAL COLOR PRINTER MODEL CP-D70DW CP-D707DW OPERATION MANUAL CP-D70DW CP-D707DW THIS OPERATION MANUAL IS IMPORTANT TO YOU. PLEASE READ IT BEFORE USING YOUR DIGITAL COLOR PRINTER. Hereby, Mitsubishi Electric Corporation, declares that this digital color printer is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. INFORMATION WARNING : This Class A digital apparatus complies with Canadian ICES-003. PRECAUTIONS TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING: FEATURES Use the included AC power cord so as not to interfere with radio and television reception. If you use other cables, it may cause interference with radio and television reception. RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION PREPARATION CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute the risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. [. . . ] Turn the spacer until the latches are locked. When you remove the spacers from the paper flanges, follow the above procedure in reverse. FEATURES PREPARATION Attachthesuppliedpaperflangestobothsidesoftheprint paper. When you pinch the latches on the paper flange, the stoppers retract into the shaft. Attach the flanges to the print paper with the stoppers retracted. Make sure that the flanges are attached to the print paper securely, and release the latches. NOTE Take care not to pinch your fingers. Do not remove the sticker on the print paper roll yet. Any slack in the print paper may degrade the print quality. CAUTION When placing the print paper, keep the print paper upright. When you put the print paper sideways, it may roll and fall. NOTE Fingerprints or dust on the paper's surface may degrade print quality and cause paper jams. Sticker TROUBLESHOOTING · · · OTHERS · · · CONTENTS INCORRECT CORRECT 11 BEFORE OPERATION Press the POWER switch on the rear panel to turn on the power. PRECAUTIONS POWER switch OPEN button After the POWER indicator's color has changed from orange to green, press the OPEN button to release the printing unit out. FEATURES Remove the paper strip bin and then pull the knob to open the door. Knob PREPARATION Place the printing paper in the correct orientation. Make sure the paper roll is firmly installed. CAUTION Do not push down on the printing unit or the door. If you push down on the printing unit or the door when they are open, this unit may fall and it can cause damage or injury. NOTE Load the paper roll slowly into the unit. If it is dropped along the ditches, the unit or accessories may be damaged. Install the print paper into the unit. TROUBLESHOOTING OTHERS Direction of paper insertion CONTENTS Remove the sticker, insert the print paper between the roller and guide as shown right, and feed the print paper until the buzzer sounds. Print paper Roller Remove the sticker before inserting the print paper between roller and guide. Buzzer continues to sound until the printing unit is closed. Dirt on the rollers may produce poor print quality. NOTE When taking the print paper out, pull it up toward you by holding the paper flanges. Make sure to turn on the power before replacing the print paper. Make sure to eliminate any slack from the print paper. If you carry out the following steps without eliminating the slack, the print paper may be damaged. · · · Guide Roller Close the door. 12 BEFORE OPERATION INK RIBBON INSTALLATION PRECAUTIONS After installing the print paper, install the ink cassette into this unit. [. . . ] Preparations Alcohol (isopropyl alcohol) Soft and clean cloth FEATURES PREPARATION 152 mm lines Printing surface When lines appear on the printed images, clean the thermal head. Wipe the head cleaning part (as shown right) carefully with cloth dampened with a small amount of alcohol. · · Do not damage the thermal head. When the poor print quality is not corrected even if the head has been cleaned, replacement of the thermal head may be required. [. . . ]