User manual MITSUBISHI CP800DW

[. . . ] DIGITAL COLOR PRINTER MODEL CP800DW OPERATION MANUAL CP800DW PAPER FEED &CUT ALARM SHEET/PAPER SCSI DATA COPY ONLINE POWER OPEN THIS OPERATION MANUAL IS IMPORTANT TO YOU. PLEASE READ IT BEFORE USING YOUR DIGITAL COLOR PRINTER. This digital colour printer complies with the requirements of the EC Directive 89/336/EEC, 73/23/EEC and 93/68/EEC. The electro-magnetic susceptibility has been chosen at a level that gains proper operation in residential areas, on business and light industrial premises and on small-scale enterprises, inside as well as outside of the buildings. All places of operation are characterised by their connection to the public low voltage power supply system. CONTENTS PRECAUTIONS CONTENTS SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] For pin connections see the table on pages 7-8. Corporation. CONNECTIONS Make sure to turn off main power of the unit and other equipment before connection. PRECAUTIONS CONNECTION WITH PARALLEL DATA INTERFACE CONNECTION PIN NO. FEATURES To PARALLEL port 18 1 To PARALLEL DATA terminal MODE switches 36 19 SCSI ID No. Connector :JD36SL equivalent (36-pin) AC LINE CONNECTIONS PREPARATION ON SCREW OFF 12345678 12345678 DIRECT SNAP ACK ON PARALLEL OFF SCSI PARALLEL Input level :TTL PARALLEL input connector port :signal allocation Personal computer Digital Color Printer See next page for PARALLEL DATA SIGNALS. 7 TROUBLESHOOTING OTHERS CONNECTIONS 2 PARALLEL DATA SIGNAL Pin No. 19 Signal STROBE From/to PC/DCP Function Strobe pulse for data reading. Incoming pulse width should be 0. 5 ms minimum. Turn the arrow to set the ID number with a screwdriver. 7 is provided for personal computer you use and No. Do not set the ID number to the same setting as the connected equipment. NOTE Make sure to turn on the power again when SCSI ID number is changed with the power turned on. 2 Setting ON LINE status POWER 1 Press POWER button to turn on this unit. The lamp over the POWER button is lit. 9 CONNECTIONS 2 Turn on the power of the personal computer connected. 3 Confirm that ON LINE button on the front panel is lit. SETTING MODE SWITCHES Set the mode switches (DIP-SW) on the rear panel according to the connected device. PAPER FEED & CUT COPY ONLINE ON OFF 12345678 12345678 DIRECT SNAP ACK ON PARALLEL OFF SCSI With the mode switch No. 1, switch parallel or SCSI. 4, set the time of acknowledge signal (ACK). Refer to the operation manual of the connected personal computer for the set time. Mode switch No. 2 3 4 ACK time 0. 5µs 1. 0µs 1. 5µs 2. 0µs 2. 5µs 3. 0µs 3. 5µs 4. 0µs OFF(down) OFF(down) OFF(down) OFF(down) OFF(down) ON(up) With the mode switches No. 7, select the printing result when connecting with DS-300 (FUJIX digital camera). Mode switch No. Printing result Normal print (Print connecting with a personal computer) Print image will not be enlarged. With the mode switch No. 8, set whether the surface lamination is applied or not. The printing speed will get faster due to the skipping surface lamination process. The printing speed is the standard speed. · When this switch is set to ON, the printing speed will get faster due to the skipping surface lamination process. However, the life, light stability, moisture resistance and fingerprint resistance will be as the same level as the print paper without surface coating. The default setting of the mode switches is OFF. Make sure to turn on the power again when the mode switch setting is changed. NOTE · On the initializing function invalid status, when printing is interrupted by the command from the host computer, turn the power of this unit to OFF and clear the transferred data. Switching position ON(up) ON(up) OFF(down) OFF(down) OFF(down) ON(up) OFF(down) ON(up) OFF(down) ON(up) OFF(down) ON(up) OFF(down) ON(up) ON(up) ON(up) ON(up) ON(up) 5 Switching position 6 7 ON/OFF OFF(down) ON/OFF ON(up) ON(up) ON(up) OFF(down) ON/OFF ON(up) ON(up) OFF(down) Print image will be enlarged to 137. 5%. ON(up) Print image will be enlarged to 137. 5% and white frame will be made around the image. 10 BEFORE OPERATION Before printing, PRECAUTIONS 1. Remove the fixed screw on the printing unit and the protective cushion. [. . . ] After pushing the printing unit until it is locked into place, press the PAPER FEED & CUT button. When this error occurs during printing on L size paper, carry out this procedure twice. 18 BEFORE CALLING FOR SERVICE Symptom No power The image is not printed. Check & Remedy · Is the power cord plug disconnected from the outlet?Connect the power cord plug to the outlet firmly. · Is the image data sent to this unit? [. . . ]