User manual MITSUBISHI CP900DW

[. . . ] DIGITAL COLOR PRINTER MODEL CP900DW OPERATION MANUAL FEED&CUT RESET COPY THIS OPERATION MANUAL IS IMPORTANT TO YOU. PLEASE READ IT BEFORE USING YOUR DIGITAL COLOR PRINTER. This digital color printer complies with the requirements of the EC Directive 89/336/EEC, 73/23/EEC, 93/42/EEC and 93/68/EEC. The electro-magnetic susceptibility has been chosen at a level that gains proper operation in residential areas, on business and light industrial premises and on small-scale enterprises, inside as well as outside of the buildings. All places of operation are characterised by their connection to the public low voltage power supply system. INFORMATION This Class A digital apparatus complies with Canadian ICES-003. [. . . ] For details, refer to the installation instruction of the equipment to be connected. Use this clamper so that the USB port is not disconnected. Connects to the provided power cord. Insert the cord firmly. 8 CONNECTIONS CONNECTION WITH USB INTERFACE PRECAUTIONS 2 CONNECTING WITH PC Connect this unit with a personal computer as following example. FEATURES To USB port 87654321 REMOTE OFF ON USB CONNECTIONS PREPARATION AC LINE To USB port Personal computer Printer TROUBLESHOOTING OTHERS 9 CONNECTIONS SETTING MODE SWITCHES 2 SETTING MODE SWITCHES Set the mode switches on the rear panel according to the equipment connected. All the switches are set to OFF as shown right when shipped from the factory. Turn off the power when changing the mode switch settings. 1 2 OFF OFF ON ON OFF ON ON OFF Print speed Prints at the speed set by the printer driver FINE mode print FAST mode print 87654321 OFF ON With the switch No. 3 to No. Settings 3 4 5 6 7 OFF ON OFF ON OFF ON OFF OFF ON 8 OFF Functions Uses the normal gamma curve of images Uses the gamma curve for connecting to ultrasound diagnostic equipment Normal print Mirror print Prints with surface coating Prints without surface coating Not used (Set this switch to OFF. ) When the printed paper remains at the print outlet, PAPER indicator blinks and this unit stops printing. Even if the printed paper remains at the print outlet, PAPER indicator remains turned off and this unit does not stop printing. Automatic feed&cut mode This will cause the printer to perform an automatic feed and cut after installation of the paper and ink sheet. ON Manual feed&cut mode 10 BEFORE OPERATION Before printing, 1. Install the print paper and ink cassette. (pages 11-15) PRECAUTIONS PAPER SHEET SET 2 PAPER SHEET SET Product name CK900S CK900L CK900S4P CK900L4P CK900S4P(HX)EU CK900L4P(HX)EU S size L size S size L size S size L size Make sure to use the following types of paper sheet and ink sheet set. FEATURES Ink sheet size No. of prints 200 130 130 90 130 90 Usage Colour print Colour print Surface-laminated colour print Surface-laminated colour print Surface-laminated colour print for ID photo Surface-laminated colour print for ID photo CONNECTIONS PREPARATION UNLOCK THE PRINTING MECHANISM 2 RELEASING THE PRINTING MECHANISM LOCK 1 1 Press down and pull the knob to extend the paper tray. 2 Shift the printing mechanism lock switch to the right (UNLOCK). (See page 8. ) 2 TROUBLESHOOTING INSTALLATION OF PRINT PAPER Do not remove the seal on the print paper yet. OTHERS Gear Seal 1 Insert the print paper roller with gear on the left. Press the folder 1 as shown right, and set the print paper roller. 1 2 Front side 11 BEFORE OPERATION 2 Set the other side of roller without gear. 1 Left side Right side 3 Remove the seal, and insert the edge of the print paper right below the roller cover with arrow marks towards the front panel. Make sure to insert the paper straight. arrow marks 4 Feed the print paper through the paper outlet. 5 Pull both sides of the print paper to eliminate slack. Paper Paper Paper 12 INSTALLATION OF INK SHEET PRECAUTIONS 2 INSTALLING THE INK SHEET Colored roller White roller Load the ink sheet roll to the ink cassette before inserting the ink cassette into the printer. 1 Insert the ink sheet rollers gear into the holes of the ink cassette. Put the white roller (rolled with ink sheet) to the ink cassette first. Then, insert the colored roller (take-up) to the ink cassette. FEATURES CONNECTIONS PREPARATION 2 Put the other sides of rollers. Set IC at this time. IC chip with the IC holder is attached to the ink sheet. Set the IC holder to the ink cassette as shown right. · · NOTE Do not remove the IC chip or IC holder from the ink sheet. Removal of the IC will stop the printer from functioning correctly. Set the projected part of the IC holder to the correct position as shown below. TROUBLESHOOTING OTHERS IC holder Projected part 2 INSTALLING THE INK CASSETTE 1 Eliminate any slack of the ink sheet. Hold the colored roller and turn the white roller. 13 BEFORE OPERATION 2 Insert the ink cassette with the ink sheet into its compartment. Put the ink cassette into the printer drawer as shown 1. Then, set the other side 1 1 (with handle) as shown right. When exchanging the ink cassette, remove it by holding the handle. [. . . ] Preparations Alcohol (isopropyl alcohol) Tissue paper (Fold in half about 4 times, and use the folded side to clean. ) Cotton buds Cleaning kit (Option)* Other : Cleaner pen (Option)* *Please ask the dealer about options. Cleaner pen (Option) Make sure to turn off the power before cleaning. Cleaning part How to hold tissue paper 1 Press OPEN button to pull the printing mechanism out. 2 Remove the ink cassette and print paper. 3 Wipe the ink sheet sensor. Clean the parts circled in the right figure. [. . . ]