User manual MITSUBISHI DIAMOND PLUS 200

[. . . ] AUTO-SCANNING WITH DIGITAL CONTROL COLOR DISPLAY MONITOR MODEL NSH1117STTKW USER'S GUIDE For future reference, record the serial number of your display monitor in the space below: SERIAL No. The serial number is located on the rear cover of the monitor. Internet Home Page: http://www. mitsubishi-display. com/ Supplying Windows 95/98 INF File download service, new product information, etc. ® -2- CONTENTS ENGLISH 1. INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 CAUTION The power cord provided with this monitor is designed for safety and must be used with a properly grounded outlet to avoid possible electrical shock. [. . . ] 3. 1 AC Power Connection 3. 2. 2 Connecting to An Apple Macintosh Computer Figure 6 shows the SC-B104 cable and AD-A205 Adapter(option) to the video port in an Apple Macintosh. For Macintosh Adapter AD-A205, contact your dealer. Power off, both the monitor and the computer. Set the DIP switches of Macintosh Adapter according to the setting chart. (See Section 7. 3 Optional Macintosh Adapter ADA205 Settings) Connect the 15-pin (DB-15P) end of the AD-A205 Adapter to the straight 15-pin connector on the Macintosh video port on the computer or on the video board. Connect the sub-miniature 15-pin (DB9-15P) end of the AD-A205 Adapter to the SC-B104 cable. Connect the other end of the SC-B104 cable to the DB9-15P receptacle on the back of the monitor. Power on the monitor, then the Macintosh. After using the system, power off the monitor, then the Macintosh. D-SUB D-SUB One end of the AC power cord is connected to the AC power connector on the back of the monitor. The other end is plugged into a properly grounded three-prong AC outlet. The monitor's auto-sensing power supply can automatically detect 100-120V AC or 220-240V AC and 50 or 60Hz. 7. The DB9-15P(VGA) connector is provided for compatible analog RGB outputs from your computer. Apple Macintosh computers can also be interfaced with using the optional Mitsubishi Macintosh adapter AD-A205. 3. 2. 1 Connecting to Any IBM VGA Compatible System Figure 5 shows the SC-B104 cable connection to the Video Graphics Array (VGA) port in an IBM Personal System/2® series, or any VGA compatible system. Power off, both the monitor and the computer. Connect the one end of the SC-B104 cable to the DB9-15P connector on the VGA controller card. Connect the other end of the SC-B104 cable to the DB9-15P receptacle on the back of the monitor. Power on the monitor, then the computer. After using the system, power off the monitor, then the computer. Computer Apple Macintosh Computer SIGNAL-A SIGNAL-B Macintosh Adapter AD-A205 (Option) Power Cord Cable SC-B104 Figure 6 · · Computer D-SUB D-SUB For the Apple Macintosh Computers having a VGA compatible port, steps 2 through 4 are not necessary. Connect the end of the signal cable to the port directly. In case of Apple Macintosh G3 series, use "Control Panel" of "Apple Menu" when selecting a resolution. If select the resolution from "Control Bar", no screen may be displayed and the computer may freeze. SIGNAL-A SIGNAL-B VGA Compatible System DB9-15P 3. 2. 3 Connecting to two computers Figure 7 shows the connection to two computers Refer to clause 3. 2. 1 or 3. 2. 2 for the connection procedure. Power Cord Cable SC-B104 Figure 5 CAUTION D-SUB D-SUB B The socket-outlet shall be installed near the equipment and shall be easily accessible. [. . . ] Position an open white window over the affected area of the screen and maximize the brightness and contrast controls. This will cause localized heating of the overlap which will clear in a few minutes. Be sure to readjust the brightness and contrast controls back to the normal viewing levels after this procedure. · ­ LOCATION Abnormal Picture Black vertical lines are visible on the screen. Two fine horizontal lines are visible on the screen. · The 2 very faint thin lines across the screen are normal. [. . . ]