User manual MITSUBISHI DIAMOND PRO 2040U

[. . . ] AUTO-SCANNING WITH DIGITAL CONTROL COLOR DISPLAY MONITOR MODEL NSB1107STTUW USER'S GUIDE For future reference, record the serial number of your display monitor in the space below: SERIAL No. The serial number is located on the rear cover of the monitor. Internet Home Page: http://www. mitsubishi-display. com/ Supplying Windows 95/98 INF File download service, new product information, etc. ® -2- CONTENTS ENGLISH 1. INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 CAUTION The power cord provided with this monitor is designed for safety and must be used with a properly grounded outlet to avoid possible electrical shock. [. . . ] During servicing, disconnect the plug from the socket-outlet. Méme si le moniteur est mis hors tension il reste toujours alimenté. La prise secteur devrait ainsi ètre facilement accssible en cas d'urgence. - 10 - 3. 2. 3 Connecting to a Unix Workstation & Third Party Graphics Card Figure 7 shows the SC-B104 or 75 coaxial cable (not supplied) connection to the graphics video card (PC-CAD and workstation). Power off, both the monitor and the computer. Connect one end of the SC-B104 cable or the 75 coaxial cable to the output connector on the computer, or on the video board. Connect the other end of the SC-B104 cable or the 75 coaxial cable to the DB9-15P receptacle or the BNC receptacles on the back of the monitor. Power on the monitor, then the computer. After using the system, power off the monitor, then the computer. 3. 2. 4 BNC Connection (1) COMPOSITE SYNC ON GREEN VIDEO SIGNAL (3 wires): Connect the R, G and B video signals to the BNC connectors on the back of the monitor. BNC A B 1 2 R G B COMP. 5. (2) EXTERNAL COMPOSITE SYNC SIGNAL(4 wires): Connect the R, G and B video signals and the Composite sync signal to BNC connectors on rear panel, respectively. BNC A D-SUB B 1 2 R G B COMP. HD VD BNC A B 1 2 R G B COMP. HD VD High Resolution Graphic Video Card D-SUB BNC R G B COMP. HD VD High Resolution Graphic Video Card coaxial cable Cable SC-B104 Power Cord 75 (3) SEPARATE HORIZONTAL AND VERTICAL SYNC SIGNALS (5 wires): Connect the R, G and B video signals and the horizontal and vertical sync signals to the BNC connectors on the rear panel. BNC Figure 7 A B 1 2 R G B COMP. HD VD 3. 3 USB System Basic Application FRONT Power Cord BACK D-SUB BNC A B 1 2 R G B COMP. HD VD Downstream Ports Downstream Port D-SUB A B 1 R G BNC B COMP. HD VD USB Cable Upstream Ports 2 Signal Cable Signal Cable NOTE USB Cable Computer Scanner The computer is required to have Windows® 98 or later installed and USB functions. When connecting one computer, either Upstream port A or B is available. The Upstream port is automatically matched with the active video input. Keyboard Camera - 11 - 3. 4 Installation of USB Function The following procedure permits your computer to recognize or "enumerate"(A USB term) the Mitsubishi USB HUB. Power on the display monitor and then the computer. Start "Enumeration" from the Windows® Desktop. (a) Disconnect and connect the USB cable to the upstream port of the display monitor. (b) Cycle power of the display monitor off then on. NOTE NOTE If the mark appears with "Generic USB HUB", then enumeration was unsuccessful. Select "Generic USB HUB" marked with mark and click "Remove" and "Refresh". After that, the enumeration is automatically started. NOTE · During the enumeration of Mitsubishi USB Hub, connect the keyboard and mouse, to the computer and not to the downstream ports on the display monitor. [. . . ] This will cause localized heating of the overlap which will clear in a few minutes. Be sure to readjust the brightness and contrast controls back to the normal viewing levels after this procedure. · ­ LOCATION Abnormal Picture Black vertical lines are visible on the screen. Two fine horizontal lines are visible on the screen. · The 2 very faint thin lines across the screen are normal. They are caused by the aperture grille stabilization filaments(Damper Wires) which are required for all aperture grille CRTs'. Aperture Grille · ­ Electron Gun Damper Wires Shadow of Damper Wires Shadow of Damper Wires Aperture Grille Type A buzzing sound when power on. · A brief vibration or hum sound that is heard just after power up is normal. [. . . ]