User manual MITSUBISHI DIAMOND PRO 87TXM

[. . . ] MITSUBISHI AUTO-SCANNING WITH DIGITAL CONTROL COLOR DISPLAY MONITOR MODEL TFM8705SKHKW USER'S GUIDE For future reference, record the serial number of your display monitor in the space below: SERIAL No. The serial number is located on the rear cover of the display. CAUTION The power cord provided with this monitor is designed for safety and must be used with a properly grounded outlet to avoid possible electrical shock. Do not remove the monitor cabinet as this can expose you to very high voltages and other hazards. ANMERKUNG: Dieser Monitor erfül lt die Anforderungen der deutschen Ergonomie-Norm ZH1/ 618/10. 80 bei Verwendung der beiden folgenden Timings: Auflöw unt 1024x768 Videoeingang Analog RGB, 0. 7Vs-s fH(kHz) fv(Hz) Interlace/Non-Interlace 60. 0 75. 0 Non-Interlaced Aus ergonomischen Gründen wird empfohlen, die Grundfarbe Blau nicht auf dunklerem Untergrund zu verwenden (schlechte Erkennbarkeit, Augenbelastung bei zu geringem Zeichenkontrast). Bei hellem Hintergrund empfehlen wir aus ergonomischen Gründen nur Vertikalfrequenzen größer oder gleich 70Hz zu verwenden. [. . . ] Save the box and packing materials in case you ship or transport the monitor. 1 2 3 4 AD -A 20 5 N O 1 2 4 I 3 SH BI SU IT M 5 6 5 6 1. Warranty-Set M I X H T 7 IS 8 B o ro U P S d T IT n o TK M K m SK ia 05 8 D M87 F T Figure 1. 1. 8 Tilt/Swivel Base The monitor comes with a tilt/swivel base. This enables you to position the monitor to the best angle and tilt for maximum viewing comfort. Screen Position Adjustment Adjust the tilt and rotation of the monitor by placing your hands at opposite sides of the case, as shown in Figure 2. You can adjust the monitor 90 degrees right or left, 15 degrees up or 5 degrees down, as shown below. 15 90 90° 15° 90 90° 5° Figure 2. 10 1. 9 Quick Operation Chart To summarize the steps in connecting your computer and adapter with Diamond Pro 87TXM color monitor and setting the necessary controls and switches, refer to the chart below. Connect the power cord to the Diamond Pro 87TXM color monitor and the signal cable between the Diamond Pro 87TXM and the graphics adapter. See 2. 1 AC Power Connection 2. 2 Signal Cable Connection Turn on the Diamond Pro 87TXM color monitor. Turn on the computer. Set the controls and switches. See 3. FUNCTION CONTROLS If a problem appears. OK GOOD See 5. TROUBLESHOOTING If the problem persists. Call for your authorized MITSUBISHI Product Support at 1-800-344-6352. 11 2 CONNECTING THE MONITOR On the back of the monitor are four plug-in connections: one for the AC power cord, DB915P and BNC Connector for video and a DIN8P connector for the optional serial interface kit. 2. 1 AC Power Connection One end of the AC power cord is connected into the AC power connector on the back of the monitor. The other end is plugged into a properly grounded three-prong AC outlet. The monitor's auto-sensing power supply can automatically detect 100-120V AC or 200-240V AC and 50 or 60Hz. 2. 2 Signal Cable Connection The attached video signal cable provides a DB9-15P connector for the VGA compatible analog RGB outputs on your computer. The RGB signal may be derived from an IBM® PS/2, or compatible, Apple Macintosh built-in video or most third party color cards can be interfaced using the AD-A205 adapter. NOTE DB9-15P and BNC receptacle cannot be used simultaneously (at the same time). If you will use DB9-15P, do not connect any of the BNC receptacles. 2. 2. 1 Connecting to Any IBM VGA Compatible System Figure 3 shows the SC-B102 cable connection to the Video Graphics Array (VGA) port in an IBM Personal System/2® Model 50, 60, 70 and 80, or any VGA compatible system. Power off, both the monitor and the computer. Connect the computer end of the SC-B102 cable to the 15-pin connector on the VGA controller card. Connect the monitor end of the SC-B102 cable to the DB9-15P receptacle on the back of the monitor. Power on the computer, then the monitor. After using the system, power off the monitor, then the computer. Computer VGA Compatible System Signal Serial R G B HD/COMP VD DB9-15P DB915P Power Cord CABLE SC-B102 Figure 3. CAUTION The socket-outlet shall be location near the equipment and shall be easily accessible. [. . . ] · Front (OSD) · Adjust H-SIZE, V-SIZE, H-PHASE, and V-POSITION with non-standard signals. · Front (OSD) · Make sure you wait a few second after adjusting the size of the image before changing or disconnecting the signal or powering OFF the monitor. Display is not stable Display is dark or too bright · BNC cables are misconnected. · Input video signal level select is not at the appropriate position for your graphics adapter output. (0. 7V or 1. 0Vp-p) · Rear · Front (OSD) 30 NOTE: Two fine horizontal lines may be visible on the screen. This is not a fault or defect of the monitor and is normal for all aperture grille type displays. [. . . ]