User manual MITSUBISHI DIAMOND PRO 900

[. . . ] AUTO-SCANNING WITH DIGITAL CONTROL COLOR DISPLAY MONITOR MITSUBISHI MODEL NFJ9905SKHUW USER'S GUIDE For future reference, record the serial number of your display monitor in the space below: SERIAL No. The serial number is located on the rear cover of the monitor. ENGLISH CAUTION The power cord provided with this monitor is designed for safety and must be used with a properly grounded outlet to avoid possible electrical shock. Do not remove the monitor cabinet as this can expose you to very high voltages and other hazards. ANMERKUNG: Dieser Monitor erfüllt die Anforderungen der deutschen Ergonomie-Norm ZH1/ 618/10. 80 bei Verwendung der beiden folgenden Timing: Auflösung Videoeingang 1280x1024 Analog RGB, 0. 7Vs-s fH(kHz) fv(Hz) Interlace/Non-Interlace 91. 1 85. 0 Non-Interlaced Aus ergonomischen Gründen wird empfohlen, die Grundfarbe Blau nicht auf dunklerem Untergrund zu verwenden (schlechte Erkennbarkeit, Augenbelastung bei zu geringem Zeichenkontrast). [. . . ] HD VD (2) IN CASE OF EXTERNAL COMPOSITE SYNC SIGNAL: Connect the R, G and B video signals and the Composite sync signal to BNC receptacles on rear panel, respectively. D-SUB BNC R G B COMP. HD VD (3) IN CASE OF SEPARATE HORIZONTAL AND VERTICAL SYNC SIGNALS: Connect the R, G and B video signals and the horizontal and vertical sync signals to the BNC receptacles on the rear panel. D-SUB BNC R G B COMP. HD VD - 1-15 - ENGLISH 3. 3 USB System Basic Application FRONT BACK D-SUB BNC R G B COMP. HD VD Upstream Ports Downstream Port A B 1 2 R G D-SUB BNC B COMP. HD VD Downstream Ports Scanner Keyboard Camera Computer NOTE The computer is required to have Windows 98 installed and USB functions. When connecting one computer, either Upstream port A or B is available. The Upstream port with that the computer is connected is detected automatically. - 1-16 - ENGLISH CAUTION Use the included ferrite core with the USB cable which is connected to the USB connectors (Downstream) to reduce the possibility of causing interference to radio, television, and other electrical devices. D-SUB BNC A B 1 2 R G B COMP. HD VD USB CONNCTOR (DOWNSTREAM) USB CABLE FERRITE CORE 1 2 HOW TO MOUNT THE FERRITE CORE Place the included ferrite core under the USB cable at approx. Then, close the plastic case until you have a clock. USB Cable USB Plug Ferrite Core Approx. (3 cm) - 1-17 - ENGLISH 3. 4 1. 2. Installation of USB Function Power on the display monitor and computer. Enumerate Mitsubishi USB HUB using the following procedure. NOTE During the enumeration of Mitsubishi USB Hub, connect the keyboard and mouse equipped with USB function, to the computer and not to the downstream ports on the display monitor. After the enumeration, the keyboard and mouse can be used by connecting to the downstream ports. (1) Insert the included floppy disk in the computer. (2) Connect the computer and the display monitor with the included USB upstream cable. (3) Install 'INF' file from the included floppy disk. (4) Click "Next" on Figure 8 to get Figure 9. (5) Click "Finish" on Figure 9 to complete the enumeration of Mitsubishi USB HUB. You can confirm that "Mitsubishi USB HUB" is successfully enumerated with the following method. · Open "Device Manager" tab in "System" property under "Control Panel". Confirm that "Mitsubishi USB Hub" or "Generic USB HUB" is listed in "Universal Serial Bus Controller". If you can't confirm it, re-enumerate "Mitsubishi USB HUB" again by following (a) or (b). [. . . ] This sound will be heard each time the monitor is powered up from a cold start and each time the manual degauss button is used. · ­ - 1-34 - 6 SPECIFICATIONS ENGLISH 50cm/19"(46cm/18" Diagonal Viewable Image) Aperture grille In-line 90° Red, Green, Blue EBU (medium short persistence) 0. 25 - 0. 27mm (variable) Anti-glare, Anti-reflection and Anti-static coating Dynamic Beam Forming (DBF) 0. 7 or 1. 0Vp-p analog RGB Sync. or Composite sync 5BNC, DB9-15P 75 (video), 1k (sync. ) Self-powered HUB complying with Universal Serial Bus Specification Rev. 1. 0. USB Monitor Control to adjust the image on USB screen by USB commands from the computer. Interface 3 Downstream ports/12Mbps, 1. 5Mbps, possible to supply 500mA max. [. . . ]