User manual MITSUBISHI DIAMOND SCAN 90E

[. . . ] MITSUBISHI AUTO-SCANNING WITH DIGITAL CONTROL COLOR DISPLAY MONITOR MODEL FFT9905SKHFW USER'S GUIDE For future reference, record the serial number of your display monitor in the space below: SERIAL No. The serial number is located on the rear cover of the monitor. CAUTION The power cord provided with this monitor is designed for safety and must be used with a properly grounded outlet to avoid possible electrical shock. Do not remove the monitor cabinet as this can expose you to very high voltages and other hazards. Trademark IBM, PC, PS/2, PS/V, Personal System/2 are registered trademarks of International Business Machines Corp. Apple Macintosh is a registered trademark of Apple Computer, Inc. [. . . ] When transporting the monitor, handle it with care. * * * * * CAUTION Keep your fingers away from the pivot area of the tilt/swivel base. 1. 6 Cleaning Your Monitor When cleaning the monitor, please follow these guidelines: * * * Always unplug the monitor before cleaning. Wipe the screen and cabinet front and sides with a soft cloth. If the screen requires more than dusting, apply a household window cleaner to a soft cloth to clean the monitor screen. CAUTION Do not use benzene, thinner or any volatile substances to clean the unit as the finish may be permanently marked. Never leave the monitor in contact with rubber or vinyl for an extended time period. 8 1. 7 Unpacking After you unpack the box you should have all of the items indicated in Figure 1. Save the box and packing materials in case you ship or transport the monitor. 1 2 3 4 5 20 -A AD O N 1 2 5 6 M O DE L FF T99 05 SK HK W 1. Warranty-Set Figure 1. M IT SU 3 4 5 6 BI SH I M M I e e H 0 9 IS n n B a U c S S d IT n o o e m ia Guid D r's G s U U e 1. 8 Tilt/Swivel Base The monitor comes with a tilt/swivel base. This enables you to position the monitor to the best angle and tilt for maximum viewing comfort. Screen Position Adjustment Adjust the tilt and rotation of the monitor by placing your hands at opposite sides of the case, as shown in Figure 2. You can adjust the monitor 45 degrees right or left, 10 degrees up or 5 degrees down, as shown below. 10 45 45 5 Figure 2. 9 1. 9 Quick Operation Chart To summarize the steps in connecting your computer and adapter with Diamond Scan 90e color monitor and setting the necessary controls and switches, refer to the chart below. Connect the power cord to the Diamond Scan 90e color monitor and the signal cable between the Diamond Scan 90e and the graphics adapter. See 2. 1 AC Power Connection 2. 2 Signal Cable Connection Turn on the computer. Turn on the Diamond Scan 90e color monitor. Set the controls and switches. See 3. FUNCTION CONTROLS If a problem appears. OK OK See 5. TROUBLESHOOTING If the problem persists. Call for your authorized MITSUBISHI Product Support at 1-800-344-6352. 10 2 CONNECTING THE MONITOR On the back of the monitor are four plug-in connections: one for the AC power cord, DB9-15P connector, BNC connector for video and a DIN-8P connector for the optional USB-unit. 2. 1 AC Power Connection One end of the AC power cord is connected into the AC power connector on the back of the monitor. The other end is plugged into a properly grounded three-prong AC outlet. The monitor's auto-sensing power supply can automatically respond to the power supply input of 100240V AC and 50/60Hz. 2. 2 Signal Cable Connection The attached video signal cable provides a DB9-15P connector for the VGA compatible analog RGB outputs on your computer. The RGB signal may be derived from an IBM® PS/2, or compatible Apple Macintosh built-in video. Most third party color cards can also be interfaced using the free Mitsubishi Apple adaptor available from your dealer. 2. 2. 1 Connecting to Any IBM VGA Compatible System Figure 3 shows the SC-B102 cable connection to the Video Graphics Array (VGA) port in an IBM Personal System/2® Model 50, 60, 70 and 80, or any VGA compatible system. Power off, the monitor and the computer. Connect the one end of the SC-B102 cable to the DB9-15P connector on the VGA controller card. Connect the other end of the SC-B102 cable to the DB9-15P receptacle on the back of the monitor. Power on the computer, then the monitor. [. . . ] · Check the power managePower management function is active. (see P23) · Rear BNC cables are misconnected. Input signal frequency range is disagreement. · Check the specification of graphics adapter and CGA MODE is not available. [. . . ]