User manual MITSUBISHI DX TL930E

[. . . ] INSTALLATION AND OPERATION MANUAL MODEL THIS INSTRUCTION MANUAL IS IMPORTANT TO YOU. PLEASE READ IT BEFORE USING YOUR DIGITAL RECORDER. 1 CASTELLANO DX-TL930E FRANÇAIS DEUTSCH DIGITAL RECORDER ENGLISH Features Unit with built-in, large-volume hard disk drive This unit realizes high-resolution playback of over 400 horizontal lines thanks to digital technology using JPEG compression. There are 5 user-selectable image quality settings. The main device also features a built-in, largevolume 30GB hard disk for both high reliability and high-speed operation. [. . . ] After confirming the elapsed time, turn the SHUTTLE ring to the left. · To exit the menu, press the INFO button again. · The elapsed time of archive device or copy device will not be reset even though those devices are disconnected. · The elapsed time of archive device includes the time when the ARCHIVE button is pressed (when pressed, the ARCHIVE button illuminates) even in the case where there is no data on the main HDD such as an alarm stand-by mode. · The elapsed time shown on this menu may not be consistent with the regulation guaranteed period of the stock of wearing parts subject to wear or the guaranteed life span. INFORMATION 2. Turn the JOG dial until the cursor is next to "CONNECTED SCSI DEVICE" and turn the SHUTTLE ring to the right. · SCSI ID numbers are shown on the screen. <CONNECTED SCSI DEVICE> SCSI ID0:HDD(30GB) ID1:HDD( 9GB) ID2:NONE ID3:NONE ID4:DDS ID5:NONE LIMIT OFF The elapsed time is shown up to 999999 hours at the maximum. 3. Turn the SHUTTLE ring to the left or press the INFO button. s Elapsed time display The elapsed time of main HDD, archive device and copy device are shown on the screen. ELAPSED TIME for ARCHIVE or COPY will not be displayed unless an ARCHIVE device or COPY device has been connected to the unit. The elapsed time of main HDD is counted while the unit's power is turned on. The elapsed time of the peripheral device (ID4) is counted as shown below: 1) While the ARCHIVE button illuminates or flashes. <ELAPSED TIME> MAIN ARCHIVE COPY 1500H 200H 120H 2) While the PLAY or REV PLAY button illuminates or flashes when the archive device is selected as a playback device using the PLAY DEVICE button. Refer to page 14, " Basic playback" for details. 3) While the ARCHIVE indicator illuminates or flashes when restoring the data from main HDD to archive device. The elapsed time of the peripheral device (ID5) is counted as shown below. 1) While the PLAY or REV PLAY button illuminates or flashes when the copy device is selected as a playback device using the PLAY DEVICE button. Refer to page 14, " Basic playback" for details. 2) While the COPY indicator illuminates or flashes when copying the data from main HDD to the copy device. 3) While the COPY indicator illuminates or flashes when restoring the data from main HDD to the copy device. ············································································································································ 32 Various recording settings This Unit has many settings for various recordings. You have to make settings on different pages for normal recording and timer recording. Please refer to the table below for details. If the channel which is to be operated on <CAMERA SETTING> is not set, the warning will appear. Recording Setting Recording by setting manually Normal recording REC P. GRADE in <RECORDING SET UP> Page Alarm recording A-REC P. GRADE in <RECORDING SET UP> page 13 A-REC DURATION A-REC P. GRADE PRE A-REC ONESHOT·FIELD 1M HIGH OFF 1 Timer recording Page Normal recording REC P. GRADE in <RECORDING SET UP> This page <RECORDING SET UP> REC INTERVAL REC P. GRADE AUDIO RECORDING 25F HIGH OFF Page Alarm recording A-REC P. GRADE in <RECORDING SET UP> Page Recording picture grade <RECORDING SET UP> REC INTERVAL REC P. GRADE AUDIO RECORDING 25F HIGH OFF page 13 A-REC DURATION A-REC P. GRADE PRE A-REC ONESHOT·FIELD 1M HIGH OFF 1 This page Recording interval REC INTERVAL in <RECORDING SET UP> <RECORDING SET UP> REC INTERVAL REC P. GRADE AUDIO RECORDING 25F HIGH OFF page 13 A-REC INTERVAL in <RECORDING SET UP> A-REC INTERVAL A-REC DURATION A-REC P. GRADE PRE A-REC 25F 1M HIGH OFF This page MODE setting in <TIMER PROGRAM> <TIMER PROGRAM> DW START END MODE WED 09:30 10:00 A-25F 2 --- --:-- --:-- ------ page 43 A-REC INTERVAL in <RECORDING SET UP> A-REC INTERVAL A-REC DURATION A-REC P. GRADE PRE A-REC 25F 1M HIGH OFF This page Recording duration A-REC DURATION in <RECORDING SET UP> A-REC INTERVAL A-REC DURATION A-REC P. GRADE PRE A-REC 25F 1M HIGH OFF This page START and END time in <TIMER PROGRAM> <TIMER PROGRAM> DW START END MODE WED 09:30 10:00 A-25F 2 --- --:-- --:-- ------ A-REC DURATION in <RECORDING SET UP> page 43 A-REC INTERVAL A-REC DURATION A-REC P. GRADE PRE A-REC 25F 1M HIGH OFF This page Selected CAMERA USAGE pattern on <MPX FUNCTIONS> Recording camera channel (CH) <MPX FUNCTIONS> CAMERA USAGE CAMERA SETTING SPLIT SCREEN SETTING Selected ALARM REC CH. setting on <MPX FUNCTIONS> page 38 <MPX FUNCTIONS> A CAMERA USAGE CAMERA SETTING SPLIT SCREEN SETTING SHARP SPLIT P. GRADE SEQUENTIAL SEP. TITLE Selected CAMERA USAGE pattern on MODE setting of <TIMER PROGRAM> page 39 <TIMER PROGRAM> DW START END MODE WED 09:30 10:00 A-25FL 2 --- --:-- --:-- ------ Selected ALARM REC CH. setting on <MPX FUNCTIONS> page 43 <MPX FUNCTIONS> A CAMERA USAGE CAMERA SETTING SPLIT SCREEN SETTING SHARP SPLIT P. GRADE SEQUENTIAL ALL ALARM REC CH. [. . . ] · Check whether the visual signal is being properly outputted. · Check whether the unit's camera setting is set to an empty channel. · Confirm that the SCSI cable is properly connected. · Inspect the HDD/archive/copy device. · Either turn off recording or, if the visual signal has been restored, cancel the warning · Press the WARNING RESET button. [. . . ]