User manual MITSUBISHI DX-TL4716U

[. . . ] DIGITAL RECORDER USERS MANUAL MODEL DX-TL4716U THIS INSTRUCTION MANUAL IS IMPORTANT TO YOU. PLEASE READ IT BEFORE USING YOUR DIGITAL RECORDER. 1 WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. i AVERTISSEMENT DANGER D'ÉLECTROCUTION NE PAS OUVRIR AVERTISSEMENT: POUR ÉLIMINER TOUT RISQUE D'ÉLECTROCUTION, NE PAS OUVRIR LE COUVERCLE (OU LA PARTIE ARRIÈRE). AUCUNE PIECE RÉPARABLE PAR L'UTILISATEUR NE SE TROUVE À L'INTÉRIEUR. POUR TOUTE INTERVENTION D'ENTRETIEN OU DE RÉPARATION SE CONFIER AUX TECHNICIENS QUALIFIÉS. La flèche symbolisant l'éclair dans un triangle équilateral a pour objet de tirer l'attention de l'utilisateur sur le fait, qu' il y a des "tensions dangereuses" non-isolées à l'intérieur de l'enceinte du produit qui peuvent être suffisamment importantes pour conduire au risque d'électrocution. Le point d'exclamation au sein d'un triangle équilateral a pour objet de tirer l'attention de l'utilisateur sur le fait qu' il y a des instructions de mise en service et d'entretien (de réparation) dans les fiches descriptives de l'appareil qui doivent obligatoirement être respectées. AVERTISSEMENT: AFIN D'ÉVITER TOUT RISQUE D'INCENDIE OU D'ÉLECTROCUTION, NE PAS EXPOSER CET APPAREIL À LA PLUIE NI À L'HUMIDITÉ. ATTENTION: POUR PRÉVENIR LES CHOCS ÉLECTRIQUES NE PAS UTILISER CETTE FICHE POLARISÉE AVEC UN PROLONGATEUR, UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT ÊTRE INSÉRÉES À FOND SANS EN LAISSER AUCUNE PARTIE À DÉCOUVERT. Beginning ii Important safeguards PLEASE READ ALL THESE INSTRUCTIONS REGARDING YOUR RECORDER AND RETAIN FOR FUTURE REFERENCE. [. . . ] This function is useful for copying the data of the short period of time. Before executing the copy, make sure that the Copy 1 device is connected and set in the <Add/Remove HDD Device> and <Add/Remove DVD/CD Drive> correctly. (System Menu Memory) User Menu 2 Copy steps When copying the data to DVD while "Overwrite" is set to "On, " the unit clears the existing data on the disc before overwriting with new data. Note that clearing the data takes about 30 to 40 minutes. You cannot cancel operation during clearing the data of the DVD. When copying the data while "Copy Data" is set to "Alarm, " the unit performs copy operation, however, the data is not copied if there is no alarm recording data within the specified range of copy. In case of CD/DVD disc, the remaining capacity becomes low because only the management information is recorded. It is recommended to carry out "Calculate" in <Copy Data to Copy 1 Drive> to confirm whether or not there is alarm recording data in the specified range. step3. 4, 5 1 Copy Data to Copy 1 Drive step 3 1 + 2 Range of Copy steps 1, 2 3 Set Copy 1 Drive step1. Set the camera number to be copied. · The button function changes between "All Off" and "All On" each time you select this button. You can switch on and off for all the cameras easily by using this button. · The picture is not copied when there is no recorded picture of the set camera number or time. Make sure to check that the picture of the specified camera has been recorded on the specified copy start point. Select "Other settings" and then set the detailed settings. From Device: Sets the device which contains the data to be copied. The available setting items are "Main" and "Copy 2. " From Group: Sets the group which contains the data to be copied. The available setting items are "Normal, " "Alarm, " and "LPA" for main, "SerialBus, " "DVD/CD, " and "Internal" for copy 2. To Copy 1: Sets the group to where the data is copied. The available setting items are "SerialBus, " "DVD/CD, " and "USBmemory. " Copy Data: Sets the data area to be copied. The available setting items are "Alarm" and "All. " Overwrite: Selects whether or not to overwrite the existed data. Auto Eject: Selects whether to eject media (CD/ DVD) automatically when the copy is over. step2. Select <Copy Data to Copy 1 Drive> and select "Start, " "Start/End, " or "End" and then select "Set. " Input the start/end time or select the bookmark of copy. Start: Sets only the start point of copy. The data is copied from the specified start point as much data as possible with the remaining capacity of the media to be copied. [. . . ] Internal temperature is getting too high, check the ventilation of the recorder. Internal temperature is getting too high, stop the operation of the recorder immediately. · Turn off the power and change the installation condition. · Turn off the power and change the installation condition. The fan of the recorder needs to be checked. [. . . ]