User manual MITSUBISHI EASY02-K60

[. . . ] OPERATOR USER´S MANUAL DPS TERMINAL Model MT1 series Easyphoto v2. 4. 0 Users Manual ENGLISH Rev 1. 9 For more information please visit www. mitsubishiphoto. com and www. easyphotosystem. com. Operator users manual TABLE OF CONTENTS 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1. 1 The best choice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1. 2 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1. 2. 1 Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] NOTE The most common USB modes used by the digital cameras are Mass Storage and PTP connection. PTP connection works better when there are only a few pictures into the camera memory: its recommended to empty the camera memory after every session when using the PTP connection. There must be at least 1 picture in the camera in order to be able to read pictures from it, too. In order to know about each camera brand/model PTP compatibility, please check the camera specifications. 30/84 Operator users manual When using a PTP or Mass Storage mode compatible Digital Camera, the operator is requested to connect it as its shown in the next picture. If an USB switch is being used between the camera and the easyphoto, now it must be switched to the position where the connection between both devices is active. When an USB switch is not being used, the digital camera USB cable should be connected to the easyphoto. When using a PTP camera, this will detect now the connection with the easyphoto system and will change to picture source mode. NOTE Please plug the camera in the rear USB port from your MT1 system. In most of the cameras using the Mass Storage mode, they have to be manually switched to this mode at this time. 3. 7. 4 Selecting the layout Afterwards, the layout must be chosen. There are two kind of layouts, standard and split. Split layouts (using two different colours) allow mixing two different pictures. After choosing the layout, the Photo ID screen is shown. 31/84 Operator users manual 3. 7. 5 Selecting and working with the pictures In the top area, the pictures read from the source are shown. When selecting any of them, the picture will be loaded to be shown in the central area. In this screen, its also possible to change the layout by clicking on the preview placed on the topright corner. The select layout screen will appear again to restart the workflow. 32/84 Operator users manual Once in the Photo ID screen again, its possible to select another picture. 3. 7. 6 Printing After pressing the "Print" button, a pop-up will appear in order to determine the amount of copies desired. When pressing the refresh button, the latest images from the picture source are reloaded. When using a camera with PTP connection, only the latest 8 images from the device are loaded. 33/84 Operator users manual 3. 7. 7 Automatic biometrics detection When automatic biometrics detection is active in the settings (see Administration chapter), it will take some more time and the picture could appear centred and zoomed. The easyphoto system is applying innovative imaging processing tools to detect the face of the customer and helping the operator of the system to center the picture in the biometrics mask shown in the centre of the screen. If a picture can not be correctly centred it appears a message under the picture just warning about it. The cause can be any of the following: The eyes of the customer are not clearly visible in the picture The top part of the head of the customer is too near the top egde of the picture. Depending on the print rectangle dimensions or aspect ratio, and also on the biometrics mask being used, this distance can vary. The customer brings glasses and there is a shiny spot of light over them. Some part of the face of the customer is not clearly visible The face of the customer in the picture is rotated 90º or more. The picture has poor vertical resolution (less than 500 pixel) Anyway, after automatic detection the picture can be manually adjusted. In some cases, even if there is not any error message in the screen, the face of the customer is not being centred correctly. If the current layout is not using the official ID or Passport dimensions and aspect ratio, and a biometrics mask is shown, this could be normal. [. . . ] Open the cover and press FEED button while Power ON 2. and wait for both LED (FEED and ERROR) blinking by return. Depress FEED then POWER LED ON, and ERROR LED OFF 4. Press FEED then, POWER LED OFF, and ERROR LED ON 5. [. . . ]