User manual MITSUBISHI EASYPHOTO DPS TERMINAL MP1

[. . . ] OPERATOR USER´S MANUAL DPS TERMINAL Model MT1 series Software version 1. 4. 0 ENGLISH For more information please visit www. mitsubishiphoto. com and www. easyphotosystem. com. Operator users manual TABLE OF CONTENTS 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1. 1 The best choice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1. 2 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1. 2. 1 Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Press "Portrait/Landscape" buttons. Press the green tic to save the changes. Press the red cross to not save the changes and escape this screen. 3. 5 Burning DVD/CD Once the "DVD/CD burning" service button is pressed, the following screen is showed: Press "Burn all" button if you want to burn not only pictures but also all the files found in the original media. 22/69 Operator users manual In this moment the screens explained from point 3. 4. 2 (Additional services: Would you like to burn a dvd or cd?) will be displayed. Press "Select photos" if you want to burn it with the selected pictures. 3. 5. 1 Selecting photos Once the "Select photos" button is pressed, the following screen is showed: For selecting the images: 1. Use the arrows to display all the images. Press "Yes" to copy it and "No" to deselect it. Press "Back" button to escape this screen. Press "Finish order" to burn it. In this moment the screens explained from point 3. 4. 3 (Additional services: Would you like to add an indexprint?) will be displayed. NOTE The DVD/CD burning service doesnt allow using a DVD/CD as a picture source. This one is disabled. 23/69 Operator users manual 3. 6 Compositions Once the "Compositions" button is pressed, the Compositions service is started. The customer is asked to insert the picture source and after following the usual workflow, the pictures can be seen at the Ordering screen. In the right panel of the screen a maximum of 4 different layouts can be shown. The available layouts depend on the selected country (in settings of the system) and the paper size of the printer. Only one picture can be selected, and also only one layout can be chosen by the end customer. When the picture is selected, its automatically allocated in the selected layout to the right panel. In the center area is possible to check the cutting area of the layout rectangle. In order to fit better the picture inside every frame or rectangle, sometimes is better to rotate the picture. After pressing the "Finish order" button, a pop-up will appear in order to determine the amount of copies desired 24/69 Operator users manual 3. 7 Photo ID (Optional) Once the "Photo ID" button (in operator mode) is pressed, or the hidden area between language selection (flags) and prices is pressed, the Photo ID service is selected. After this, depending on the system setup, its necessary to follow the source selection workflow or it can be avoided if the operator is using always the same digital picture files source (see the Administration and Settings chapter for more information) As instance, if the operator is using always a digital camera to take the pictures and this camera uses a Compact Flash, this can be indicated in settings and the application wont ask the operator where the pictures must be read from. It will search directly for the Compact Flash. There are two kind of layouts, standard and split. Split layouts (using two different colours) allow mixing two different pictures. After choosing the layout, the Photo ID screen is showed: In the top area the pictures read from the source are shown. When selecting any of them, the picture will be loaded to be shown in the central area. 25/69 Operator users manual NEW In this screen, its also possible to change the layout by clicking on the preview placed on the top right corner. The select layout screen will appear again to restart the workflow. Once in the Photo ID screen again, its possible to select another picture. 26/69 Operator users manual NEW After pressing the "Print" button, a pop-up will appear in order to determine the amount of copies desired. 3. 7. 1 Automatic biometrics detection When automatic biometrics detection is active in the settings (see Administration chapter), it will take some more time and the picture could appear centred and zoomed. [. . . ] Open the cover and press FEED button while Power ON 2. and wait for both LED (FEED and ERROR) blinking by return. Depress FEED then POWER LED ON, and ERROR LED OFF 4. Press FEED then, POWER LED OFF, and ERROR LED ON 5. [. . . ]