User manual MITSUBISHI EW331U-ST

[. . . ] DLP™ PROJECTOR MODEL EX321U-ST/EW331U-ST User Manual EX321U-ST/EW331U-ST This User Manual is important to you. Please read it before using your projector. ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. WARNING Use the attached specified power supply cord. If you use another power supply cord, it may cause interference with radio and television reception. [. . . ] Press the key repeatedly until the picture size is suitable for your need. Use the directional arrows ( , , , ) on the projector or remote control to navigate the picture. To restore the picture to its original size, press AUTO. When the key is pressed again, the picture is further reduced until it is restored to the original size. Using the OSD menu Press MENU/EXIT and then press / until the DISPLAY menu is highlighted. Press to highlight Magnify and press MODE/ENTER. Repeat steps 2-4 in the section of "Using the remote control" above. Or if you are using the projector control panel, continue to the following steps. Press on the projector repeatedly to magnify the picture to a desired size. To navigate the picture, press MODE/ENTER to switch to the panning mode and press the directional arrows ( , , , ) to navigate the picture. Use the directional arrows ( , , , ) on the projector or remote control to navigate the picture. To reduce size of the picture, press MODE/ENTER to switch back to the zoom in/out functionality, and press AUTO to restore the picture to its original size. You can also press repeatedly until it is restored to the original size. • 1. 7. The picture can only be navigated after the picture is magnified. You can further magnify the picture while searching for details. Selecting the aspect ratio The 'aspect ratio' is the ratio of the image width to the image height. Most analog TV and computers are in 4:3 ratio, and digital TV and DVDs are usually in 16:9 ratio. With the advent of digital signal processing, digital display devices like this projector can dynamically stretch and scale the image output to a different aspect than that of the image input signal. To change the projected image ratio (no matter what aspect the source is): 1. Press MENU/EXIT and then press / until the DISPLAY menu is highlighted. Press / to select an aspect ratio to suit the format of the video signal and your display requirements. EN-26 In the pictures below, the black portions are inactive areas and the white portions are active areas. OSD menus can be displayed on those unused black areas. EX321U-ST EW331U-ST 1. Auto: Scales an image proportionally to fit the projector's native resolution in its horizontal width or its vertical height. [. . . ] Stand within 8 meters (26 feet) of the projector. The password is incorrect Cause You do not remember the password. Remedy Please see "Entering the password recall procedure" on page 23 for details. The LAN function cannot be used Cause LAN control settings or LAN cable connection are problematic. The web page is not shown in the web browser or the web page is not responding. Remedy Verify the LAN control settings. Please see "Configuring the LAN Control Settings" on page 36 for details. Make sure the LAN cables are properly connected. [. . . ]