User manual MITSUBISHI GB-50A FOR INITIAL SETTING WEB

[. . . ] Mitsubishi Electric Building Air-conditioner Control System Central Controller G-50A/GB-50A Operation Manual for Initial Setting Web Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1-1 Conventions Used in This Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1-2 Computer Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1-3 Notes on using G-50A with the integrated centralized control software (TG-2000A). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 Setting the Operating Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2-1 Setting the PC IP Address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The ones that are selected will be shown with a yellow-green background. To cancel the selection, click on them again. Deselected items will be shown with a gray background. Note: The combined number of system controllers and remote controls cannot exceed four. Note: K-transmission converters do not need to be registered. 14 4-4 Interlocked Setting To interlock the operation of LOSSNAY with the run/stop status of the indoor units, click on [Initial Settings]-[Interlocked LOSSNAY] in the menu to bring up the Interlocked LOSSNAY screen, and enter the interlock conditions. Click [Save Settings] to send setting data to the G-50A. Note: If the user logs in as a building manager, the operations may be prohibited. Note: If the system is connected to the TG-2000A, make all settings and changes from the TG-2000A so that the data in TG-2000A and G-50A will match. Interlocked LOSSNAY Registration Register the interlocked ventilation equipment here. Click to bring up the registration screen. Interlocked Indoor Units Registration Register the indoor units to which LOSSNAY units are interlocked here. Click to bring up the registration screen. Refresh Read setting data from G-50A. Save Settings Send setting data to G-50A. (1) Click in the Interlocked LOSSNAY registration field to display the [Select Unit Addresses] screen, and click on the numbers corresponding to the units to be registered. The ones that are selected will be shown with a yellow-green background. To cancel the selection, click on them again. Deselected items will be shown with a gray background. (2) Click on the Interlocked Indoor Unit Registration field to display the [Select Unit Address] for the indoor units, and click on the numbers corresponding to the units to be registered. The ones that are selected will be shown with a yellow-green background. To cancel the selection, click on them again. Deselected items will be shown with a gray background. Note: A maximum of 16 indoor units can be registered to operate with one ventilator. 15 4-5 Block Setting By performing block settings, multiples of air conditioner groups can be collectively monitored or operated from the Web or TG-2000A. It also enables energy-save/peak cut controls. Bring up the Block Setting screen by clicking [Initial Settings]-[Blocks] in the menu, and register the groups in the block to utilize these features. Click [Save Settings] to send setting data to the G-50A. Note: If the user logs in as a building manager, some of the operations may be prohibited. Note: If the system is connected to the TG-2000A, make all settings and changes from the TG-2000A so that the data in TG-2000A and G-50A will match. Block Name Register the block name to be displayed on the Web screen here. Group Registration Register the groups to be included in the block here. Refresh Read setting data from G-50A. Save Settings Send setting data to G-50A. 4-5-1 Registering a block name In the [Block Name] field on the screen, register the block name to be displayed on the Web screen, using a name consisting of no more than 20 characters Note: The following characters cannot be used in the group name: < > & " ` 4-5-2 Registering a group in a block Click on the Group Registration field to display [Select Groups], and click on the numbers corresponding to the groups to be registered. The ones that are selected will be shown with a yellow-green background. (Putting a cursor on the group number will display the group name. ) To cancel the selection, click on them again. Deselected items will be shown with a gray background. 16 5 Functions 1 5-1 Error mail reports/E-mail communication Click on [Functions 1] ­ [E-Mail] in the menu to open the [E-mail] window and make necessary settings to perform remote monitoring via mail, using error mail report or the maintenance tool. Click [Save Settings] to send setting data to the G-50A. Note: The use of the error mail report function requires a separate license registration. [. . . ] Therefore, some rooms may be hotter or colder than others. Note: If the user logs in as a building manager, the operations may be prohibited. Target outdoor units The M-NET address of the outdoor unit is displayed here. Member group The group name that is connected to the outdoor unit is displayed here. When the representative group mode is selected, select the representative group among these member groups. Changeover mode The changeover mode is displayed here. Refresh Read setting data from G-50A. Save settings Send setting data to G-50A. (1) Select the change mode of the target outdoor unit. When selecting the representative group mode, select one representative group among the member groups. [. . . ]