User manual MITSUBISHI HC1500

[. . . ] DLPTM PROJECTOR MODEL HC1500 User Manual HC1500 This User Manual is important to you. Please read it before using your projector. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. WARNING Use the attached specified power supply cord. If you use another power supply cord, it may cause interference with radio and television reception. Use the attached RGB cable and RS-232C cable with this equipment so as to keep interference within the limit of a FCC Class B device. [. . . ] (See page 27. ) Use to adjust the brightness of the projected image. (See page 27. ) Use to adjust the color temperature. (See page 28. ) Use to adjust the color thickness of the projected image. (See page 27. ) Use to adjust the color tint of the projected image. (See page 27. ) Use to adjust the sharpness of the projected image. (See page 27. ) Use to adjust the BrilliantColorTM function. Use to adjust the position (height) of the projected image. · BrilliantColorTM uses BrilliantColorTM technology of Texas Instruments in USA. When you set this item to other than 0, the projector displays higher resolution images while reproducing superior colors. · By using the AV memory function, you can save up to 3 setting patterns of IMAGE menu for each input terminal. (See page 26. ) EN-24 Menu operation (continued) 2. INSTALLATION menu ITEM SETTING LAMP MODE STANDARD LOW LAMP TIME (LOW) ****H FUNCTION Select this option when you want to view images in a well-lit room. Select to moderate the intensity of the lamp. The fan operating sound is reduced and the lamp lifetime becomes longer. This item shows a lamp operating time (hour) when LAMP MODE is LOW. · When the LAMP MODE is STANDARD, this item shows a longer lamp operating time than the actual time. (See page 31 for the interval of lamp replacement. ) When ON is chosen, the lamp is automatically lit when the power cord is plugged in the wall outlet. Choose ON when using the projector mounted on the ceiling. · The projector is in the stand-by mode when the lamp is off. Use the remote control to turn on the lamp. Use to set the time elapsed before the projector enters the stand-by mode when there is no signal input from the source. Choose ON to display the splash screen when the power is turned on. [. . . ] · This projector doesn't support video devices having 4 lines (R, G, B, CS*), and 480i, 576i and 480p signals from video devices having 5 lines (R, G, B, H, V). * : Composite Sync Connectors SERIAL (8-pin) 12 COMPUTER IN/COMPONENT VIDEO IN (Mini D-SUB 15-pin) 5 10 1 Pin No. R(RED)/CR G(GREEN)/Y B(BLUE)/CB GND GND GND GND GND DDC 5V GND GND DDC Data HD/CS VD DDC Clock HDMI IN (HDMI 19-pin) 1 19 6 15 11 3 5 1 2 3 4 5 6 2 18 PIN No. 1 2 3 4 5 6 7 8 9 10 SPEC TMDS Data2+ TMDS Data2 Shield TMDS Data2TMDS Data1+ TMDS Data1 Shield TMDS Data1TMDS Data0+ TMDS Data02 Shield TMDS Data0TMDS Clock+ PIN No. [. . . ]