User manual MITSUBISHI HC3100

[. . . ] DLPTM PROJECTOR MODEL HC3100 User Manual HC3100 This User Manual is important to you. Please read it before using your projector. ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. WARNING Use the attached specified power supply cord. If you use another power supply cord, it may cause interference with radio and television reception. [. . . ] This item shows a lamp operating time (hour) when LAMP MODE is LOW. · When the LAMP MODE is STANDARD, this item shows a longer lamp operating time than the actual time. (See page 33 for the interval of lamp replacement. ) Use to change the rotation speed of the color wheel. When ON is chosen, the lamp is automatically lit when the power cord is plugged in the wall outlet. Choose ON when using the projector mounted on the ceiling. · The projector is in the stand-by mode when the lamp is off. Use the remote control to turn on the lamp. Use to set the time elapsed before the projector enters the stand-by mode when there is no signal input from the source. Choose ON to display the splash screen when the power is turned on. Use to change the color of the screen that appears when no signal is supplied. Select when viewing images from the front with the projector installed on the floor. Select when viewing images projected from the behind of the screen with the projector installed on the floor. Select when viewing images projected from the behind of the screen with the projector installed on the ceiling. Select when viewing images from the front with the projector installed on the ceiling. Choose ON to output the trigger output signal (12 V) from the TRIGGER terminal when the lamp illuminates. Select to show the test cross hatch pattern. Select to show the maximum brightness image. Select to show the minimum brightness image. When LAMP MODE has been set to LOW, the lamp mode changes from STANDARD to LOW about one minute after turn-on. When the lamp mode is switched, the projected image may flicker. Do not change the setting of LAMP MODE frequently. To cancel the test pattern, press any button. EN-25 ENGLISH Menu operation (continued) 3. FEATURE menu ITEM SETTING ASPECT AUTO 4:3 16:9 ZOOM1 ZOOM2 STRETCH REAL PASSWORD FUNCTION MENU POSITION CINEMA MODE VIDEO SIGNAL WXGA 2 options AUTO OFF 8 options AUTO 1280 x 768 etc. [. . . ] · This projector doesn't support 480i, 576i and 480p signals from video devices having 5 lines (R, G, B, H, V) or 4 lines (R, G, B, CS*). * : Composite Sync Connectors SERIAL (8-pin) 3 6 Pin No. 1 2 3 4 5 6 7 8 Name TXD GND RXD - COMPUTER IN/COMPONENT VIDEO IN (Mini D-SUB 15-pin) 12 10 5 1 Pin No. R(RED)/CR G(GREEN)/Y B(BLUE)/CB GND GND GND GND GND DDC 5V GND GND DDC Data HD/CS VD DDC Clock HDMI IN (HDMI 19-pin) 1 19 6 15 11 5 8 I/O IN OUT - 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 2 18 PIN No. [. . . ]