User manual MITSUBISHI HC3200

[. . . ] DLPTM PROJECTOR MODEL HC3200 User Manual HC3200 This User Manual is important to you. Please read it before using your projector. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: CAUTION: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. [. . . ] Select to moderate the intensity of the lamp. The fan operating sound is reduced and the lamp lifetime becomes longer. When ON is chosen, the lamp is automatically lit when the power cord is plugged in the wall outlet. Choose ON when using the projector mounted on the ceiling. · The projector is in the stand-by mode when the lamp is off. Use the remote control to turn on the lamp. Use to set the time elapsed before the projector enters the stand-by mode when there is no signal input from the source. Choose ON to display the splash screen when the power is turned on. Use to change the color of the screen that appears when no signal is supplied. Select when viewing images from the front with the projector installed on the floor. Select when viewing images projected from the behind of the screen with the projector installed on the floor. Select when viewing images projected from the behind of the screen with the projector installed on the ceiling. Select when viewing images from the front with the projector installed on the ceiling. The trigger output signal (1 V) is output from the TRIGGER terminal when the lamp illuminates. The trigger output signal (1 V) is output from the TRIGGER terminal when the aspect ratio is set to ANAMORPHIC 1 or ANAMORPHIC . The trigger output signal (1V) isn't output. Select to show the test cross hatch pattern. Select to show the maximum brightness image. Select to show the minimum brightness image. AUTO POWER ON AUTO POWER OFF SPLASH SCREEN BACK COLOR IMAGE REVERSE OFF / 5 - 60min ON / OFF BLUE / BLACK OFF MIRROR INVERT MIRROR INVERT TRIGGER OUT SCREEN ANAMORPHIC OFF CROSS HATCH WHITE BLACK TEST PATTERN · · · · The STANDARD lamp mode is activated by default whenever the projector is turned on. When the LOW LAMP MODE has been chosen, the default STANDARD lamp mode is switched to the LOW lamp mode in 1 minute. When the lamp mode is switched, the projected image may flicker. Do not change the setting of LAMP MODE frequently. [. . . ] · If the resolution and frequency of your computer aren't shown on the table, find the compatible resolution and frequency by changing the resolution of your computer. · This projector doesn't support 480p signals from video devices having 4 lines (R, G, B, CS*) or having 5 lines (R, G, B, H, V). * : Composite Sync EN-46 Specifications (continued) Connectors 12 4 3 5 SERIAL (Mini DIN 8-pin) COMPUTER IN/COMPONENT VIDEO IN (Mini D-SUB 15-pin) 5 10 1 6 15 11 Spec. R(RED)/PR/CR G(GREEN)/Y B(BLUE)/PB/CB GND GND GND GND GND DDC 5V GND GND DDC Data HD/CS VD DDC Clock HDMI IN (HDMI 19-pin) 1 19 67 8 18 Pin No. [. . . ]