User manual MITSUBISHI HS-HD2000U Owners Guide

[. . . ] VIDEO CASSETTE RECORDER OWNER'S GUIDE HIGH DEFINITION DIGITAL VCR MODEL HS-HD2000U 3 VCR Plus+, C , ALLSET and PlusCode are trademarks of Gemstar Development Corporation. The VCR Plus+ system is manufactured under license from Gemstar Development Corporation. With the VCR Plus+ GOLD system, this video cassette recorder can automatically select the appropriate channel on your compatible cable box or satellite receiver. MTP NTSC This Video Cassette Recorder is based on the D-VHS, S-VHS and VHS formats. Only video cassette tapes with the mark, mark or the mark may be used with this model. [. . . ] 12 When you are finished entering the programs you wish to record, check the following: · If you have a cable box, a digital cable box, a PRIMESTAR® or a DISH NetworkTM satellite receiver, leave the cable box or receiver turned ON. · If your VCR does not control your cable box, leave the box tuned to the station you wish to record. · Turn the VCR power OFF and make sure the programmed recording light is lit. IMPORTANT When programmed recordings of 4 and under are entered, only 4 of the 8 program lines appear on the Recap screen at any one time. To see additional program lines, turn the ADJUST dial to scroll the lines on the screen. ¬Program to record Channel 2 Day Monday 12 Start time 11:30am Stop time 1:30pm Record speed SP Use ADJUST to select, and ENTER. Press MENU to go back. Recap screen ¬Program to record CH DAY ON OFF 10 TH15 9:00p10:30pSP § 2 MO12 11:30a 1:30pSP --- ---:-- --:-- SP --- ---:-- --:-- SP Use ADJUST to select, and ENTER. Press MENU to go back. Cancelling a Recording in Progress There are two ways to cancel a recording in progress: Press STOP. The recording stops, but the program is not cancelled. Therefore, if you press REC, the recording will start again. The recording stops and the program is cancelled. Programming not cancelled STOP STOP Programming cancelled POWER Changing while Programming To change one of your settings (such as start time) while you are programming: Turn the SHUTTLE ring to the right to move forward through the program list. Turn the SHUTTLE ring to the left to move backward. Then use ADJUST dial to change the setting. You will cancel the entire program if you turn the shuttle ring to the left while the channel number is flashing. backward ADJUST forward shuttle ring 41 Timer Recording VCR Plus+® System Programming The VCR Plus+ system allows you to program your VCR to record by simply entering a PlusCode programming number. You can find this number in TV Guide or possibly your local TV listings. There are 2 ways of using VCR Plus+ System Programming on the HS-HD2000U. You can use either of the 2 following sections, VCR Plus+ System Programming Using the On Screen Display or VCR Plus+ System Programming Using the Remote Control LCD. VCR Plus+ System Programming Using the On Screen Display 1 2 Load a tape with its erasure prevention tab intact into the VCR. Turn the ADJUST dial to select Program to record. IMPORTANT If the VCR memory is full, Program memory is full will appear for 3 seconds, and then the Recap screen will appear. Use CANCEL to erase an entry before you can add another one. If there is at least one programmed recording already entered, the Recap screen will appear. Wait 4 seconds, and the VCR Plus+ system menu will appear. Use the number buttons on the remote control to enter the PlusCode number for the television show you want to record. [. . . ] Parts used for replacement are warranted for the remainder of the original warranty period. For ninety days from the date of original purchase at retail, we will provide the labor for a warranty repair without charge at an authorized MITSUBISHI service center. To obtain warranty service, you must notify an authorized MITSUBISHI service center of any defect within the applicable warranty time period. 1 TO OBTAIN WARRANTY SERVICE, deliver your VCR to the nearest MITSUBISHI service center. [. . . ]