User manual MITSUBISHI HS-U778

[. . . ] VIDEO CASSETTE RECORDER OWNER'S GUIDE VCR POWE R CHANNE L VOLUM E POTV WER EJECT MUTE 1 4 7 QUICK PROGRA M 2 CM SKI P 3 6 9 INPUT 5 8 0 VCR Plu s+ PLAY X2 VCR TV REW FF REC STOP PAUSE LIGHTI DISPLA Y NG POWER EJECT REC SPEED PLAY REW FF INDEX SP/EP AUDIO/V IDEO ADJUS CANCEL T ENTER MENU CHANNEL STOP PAUSE REC VCR/TV SP/EP ADJUS T OPEN 1 START TIME 2 REC LENGTH OTR 2 MODEL HS-U778 VCR Plus+ and PlusCode are registered trademarks of Gemstar Development Corporation. The VCR Plus+ system is manufactured under license from Gemstar Development Corporation. With VCR Plus+C3 system, this video cassette recorder can automatically select the appropriate channel on your compatible cable box or satellite receiver. C 3 and VCR Plus+C3 are trademarks of Gemstar Development Corporation. [. . . ] When you are finished with all programming, check the following: · If you have a cable box, a digital cable box, a PRIMESTAR® or a DISH NetworkTM satellite receiver, leave the cable box or receiver turned ON. · If your VCR does not control your cable box, leave the box tuned to the station you wish to record. · Turn the VCR power OFF and make sure the programmed recording light is lit. Recap screen ¬Program to record CH DAY ON OFF § 2 MO11 11:30a 1:30pSP --- ---:-- --:-- SP --- ---:-- --:-- SP --- ---:-- --:-- SP INPUT to correct channel ADJUST to select ¥ENTER to enter ADJUST to select 8 9 POWER If you want to stop the programmed recording after it starts, press POWER on the front panel. 32 Timer Recording Timer Recording Hints To use the VCR before timer recording begins, press POWER on the remote once. This turns the programmed recording light off and the VCR on. If you use POWER on the front panel for this purpose, press it twice. Pressing it once turns off the programmed recording light; pressing it again turns the VCR on. When you are finished using the VCR, turn the VCR power off again. Make sure the programmed recording light is back on. After a program has been recorded, the VCR memory of that program is cleared (unless you have scheduled the VCR to record the program every day or every week). If there is already a program in the VCR's memory, you will see the Recap screen when you bring up the menus for programming to record (unless you are programming with the QUICK PROGRAM/VCR Plus+). If the VCR's memory is full, Program memory is full will appear on the screen. If so, you must erase a program before you can enter a new one. If a tape runs out during timer recording, the VCR ejects the tape and the programmed recording light and the tape status symbol will flash. If you forget to load a tape, the programmed recording light and the tape status symbol will flash when you turn the VCR power off (A tape without an erasure tab will be ejected. To correct this, load a tape with its erasure tab intact, and turn off the VCR. ). Do not overlap the recording times you enter into the VCR. If you set two programmed recording times overlap, VCR is already programmed for that time will appear on your screen. Remember that the VCR will record over the next section of tape. If you want to save a tape, remove it and instead use a different tape for a new recording. Your VCR will not record over a tape that has the erasure prevention tab removed. All rental movies have this tab removed, so they are safe from being accidentally erased. 1 4 7 2 5 8 0 3 6 9 X2 VCR POWER 1 4 7 2 5 8 0 3 6 9 X2 POWER PROG REC PROG REC REC PROG REC REC 2 REC LENGTH PROG REC Auto speed programming Use auto speed programming if you want to record as much of the program as possible in standard play (SP) speed, but you want the VCR to automatically switch to extended play (EP) if there is not enough tape left. Auto speed programming is only available for one program. [. . . ] For one year from the date of original purchase at retail, we will repair or replace, at our option, any defective part including the video head without charge for the part. Parts used for replacement are warranted for the remainder of the original warranty period. For ninety days from the date of original purchase at retail, we will provide the labor for a warranty repair without charge at an authorized MITSUBISHI service center. T obtain warranty service, you must notify an authorized MITSUBISHI service center of any defect within the applicable warranty time period. [. . . ]