User manual MITSUBISHI LDT551V

[. . . ] Index Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . English-2 Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . English-3 Declaration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . English-5 Safety Precautions, Maintenance & Recommended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · To supply a power to the CAT5 Tx BOX, connect a USB cable also. · To CAT5 output, the signal same as RGB3, RGB4 or OPTION selected at the input switching is output. Allowable cable length Connection One monitor Multiple monitors Max. cable length/signal timing 150 m / 1920 x 1080 @60 Hz 200 m / 1920 x 1080 @60 Hz (Total length of the connected cables) The lengths given above are based on the actual measurements using our standard signal source and the recommended cable as follows. Before installation, check the monitor operation in advance by connecting it with your computer and cables. Recommended cable: 8-pin modular connector, straight-through, shielded, Category 5 or 5e Commercially available cables that passed the compatibility test: 7929A of Belden, NFTP-C5e-GY of Nex1 English-23 English P-6 Connecting RS-232C Monitor control via RS-232C Carry out as necessary To control this monitor from a computer via a communication, connect this monitor and the computer using an RS-232C cable (commercially available). How to connect · · · Turn off the main power switch of the computer and this monitor. If you make a connection while the power is on, it causes a failure of the devices. Connect the computer and this monitor using a reverse type RS-232C cable (commercially available). In addition, when you connect two or more monitors as shown in the illustration below, connect the RS-232C OUT connector of the first monitor and the RS-232C IN connector of the second monitor using a reverse type RS-232C cable (commercially available). By repeating the connection in the similar way, you can connect monitors in a daisy chain configuration. Computer (RS-232C connection) RS-232C cable RS-232C RS-232C OUT RS-232C IN RS-232C OUT RS-232C IN Left side of LCD monitor (first monitor) RS-232C cable Left side of LCD monitor (second monitor) NOTE: When only the 25-pin serial port is equipped as the serial communication port on the computer, a conversion adapter (commercially available) is necessary for the connection. English-24 P-7 Connecting LAN Monitor connection using LAN Carry out as necessary How to connect · · · · Turn off the main power switch of the computer and this monitor. If you make a connection while the power is on, it causes a failure of the devices. Connect the computer and the LAN hub using a straight type LAN cable (commercially available). Connect this monitor and the LAN hub using a straight type LAN cable (commercially available). When you connect two or more monitors, you can connect the monitor and the LAN hub using a straight type LAN cable (commercially available) as described above. Computer (LAN connection) Left side of LCD monitor LAN LAN cable LAN hub LAN hub LAN cable LAN hub LAN CAUTION: Do not connect the CAT5 IN or the CAT5 OUT connector to the LAN connector. If connected, both of the connectors may fail. NOTE: · When you use a cross type LAN cable (commercially available), you can connect the monitor and the computer one-to-one without using a LAN hub, however, the computer may not be supported. It is recommended to check the operation in advance. · The image transfer function via the LAN isn't supported. This monitor isn't equipped with the host function for controlling other devices. English-25 English As shown in the illustration below, you can connect this monitor and a computer in network through a LAN hub. Connect the monitor and the LAN hub using a straight type LAN cable (commercially available). P-8 Connecting a USB device Carry out as necessary Connecting multiple USB devices using the USB hub function You can connect up to four USB devices to the monitor if you connect the USB hub of this monitor to a computer with the USB cable (Standard A plug ­ Standard B plug) (commercially available). 1. Connect the B plug of the USB cable to the USB upstream port of this monitor. [. . . ] · Use the OSD Image Adjust controls to focus and adjust the display by increasing or decreasing the fine adjustment. When the display mode is changed, the OSD Image Adjust settings may need to be re-adjusted. · Check the monitor and your display card with respect to the compatibility and recommended signal timings. · If the displayed text is garbled, change the video mode to the non-interlace mode and use 60 Hz refresh rate. [. . . ]