User manual MITSUBISHI LVP-X300U

[. . . ] LCD Projector User Manual X300 MODEL LVP-X300U EN ­ 1 APPENDIX ESPAÑOL ITALANO DEUTSCH FRANÇAIS ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. WARNING Use the attached specified power supply cord. If you use another power-supply cord, it may cause interference with radio and television reception. [. . . ] For AUTO POWER ON ON normal use, select 0°. You can use it only when IMAGE AUTO POWER OFF 0 min REVERSE is (Invert) or (Mirror invert). To select whether to boot up automatically when the power is turned on external to the projector. In this case, the main power switch of the projector has to be ON. Set this when the projector is hanging on the ceiling. · The projector is in stand-by mode when the lamp is not on. In this case, use the remote control to turn on the lamp. Use to select the length of time before projector switches to stand-by when there is no input signal selected source. Use to display the built-in test patterns on the screen. · The display will disappear when the setting is OFF or when you press any button except MENU, { , }, STILL, LASER, mouse pointer or R/L-click. Opt 4 OPTION MENU POSITION . Use to select the position where the menu is displayed, (upper left) or (lower right). Use to display the mode display on the screen. Use to display the splash screen on the screen when the MODE DISPLAY ON power is turned ON. When AUTO is set, the video signal is processed CINEMA MODE AUTO appropriately for cinema source during inputting the AUTO cinema source with NTSC format. VIDEO SIGNAL LANGUAGE English processed during inputting the other source, set to OFF. Ë · When setting CINEMA MODE to AUTO, some images may not switch to cinema mode during inputting the cinema source. · When setting CINEMA MODE to AUTO, images may not switch to video mode immediately after switching the cinema source to video source. At that time, the image quality of the video source may get worse. If you wish to switch the mode immediately, press ENTER button. When AUTO is set, the appropriate video format is automatically selected according to the input signal. If the image does not appear correctly, select the desired video format manually. Adjust the unit to the appropriate format when the unit either is not projecting normally in auto mode or is projecting PAL-M/PAL-N signals. [. . . ] 30 30 21 0D '0' '0' '!' ' ' Status code from projector Meaning Command for POWER ON 30 30 21 0D '0' '0' '!' ' ' Command received (Command echo back) 4) Operation commands The operation commands execute the basic operation setting of this projector. It may not operate when changing the signal. Operation POWER ON POWER OFF INPUT COMPUTER 1 INPUT COMPUTER 2 INPUT VIDEO 1 INPUT VIDEO 2 ASCII !" _r1 _r2 _v1 _v2 HEX 21h 22h 5Fh 5Fh 5Fh 5Fh 72h 72h 76h 76h 31h 32h 31h 32h · POWER OFF command will not work for 1 minute after the power is turned on. · POWER ON command will not work for 1 minute after the power is turned off. [. . . ]