User manual MITSUBISHI LVP-X30U

[. . . ] Data Projector User Manual X30 MODEL LVP-X30U ESPAÑOL ITALIANO DEUTSCH FRANÇAIS ENGLISH Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. IMPORTANT Digital Light Processing, DLP, Digital Micromirror Device and DMD are all trademarks of Texas Instruments. [. . . ] If a menu is being displayed, distortion of the menu will not be corrected. Using the unit (continued) Using the Remote Control (Input Selection) 9 10 Adjust the picture elements (see page 22), then select the picture type according to the video content (see page 26). MOUSE MENU POWER Start using the unit. The following functions are available while using the unit: · Adjusting the volume of the unit's speaker (see pages 18 and 28), · Turning off the image and muting the sound temporarily (see page 18), · Freezing a moving picture (see page 18), · Enlarging the picture (see page 19) Note · When there is no signal input for a period of 5 min. or more, the power is automatically turned off and standby status is activated. (see page 29) VIDEO button VIDEO CANCEL RGB RGB button Operating from the main unit Inputs can be selected not only by operating the remote control but also by using the main unit SOURCE button. POWER STATUS POWER SOURCE AUTO SOURCE button 1 Press the VIDEO button. The video signal (VIDEO, S-VIDEO) connected to the input jack of this device will be detected and projected automatically. If a video signal is not detected, the message NO SIGNAL will be displayed. After using the unit VIDEO 1 Press the POWER button of the remote control or the POWER button of the main unit for a few seconds. The power will turn off and the POWER indicator will blink amber for 1 min. , then the standby status will be activated. (The exhaust fan will continue to run for a while for cooling purposes. ) Do not unplug the power cord while the indicator is blinking. MOUSE MENU VIDEO CANCEL RGB POWER POWER ST 2 Press the RGB button. The analog RGB signal connected to the input connector of this device will be detected and projected automatically. (Component video will be detected if the RGB/ YCbCr connector is set (page 27) to YCbCr. ) If a video signal is not detected, the message NO SIGNAL will be displayed. RGB POWER Note Blinks amber (1 min. ) Lights amber Note · All video signals input to this device will be detected if Auto Source (page 29) is set. 3 Press the SOURCE button. The video signal (RGB or YCbCr, VIDEO, SVIDEO) connected to the input jack of this device will automatically be detected and projected. If a video signal is not detected, the message NO SIGNAL will be displayed. SOURCE · The POWER switches of the remote control and main unit will not operate until the blinking stops. · After the standby status is activated, wait 1 min. or more before turning the power on again. The power will not turn on until the 1 min. · The exhaust fan will continue to run even in standby status. 2 Disconnect the power cord. The POWER indicator will turn off. The signals are sensed repeatedly in the sequence shown below. RGB/YCbCr S-VIDEO VIDEO Note · When Auto Source (see page 29) is set to ON, all signals input to this projector will be sensed. E ­ 16 Using the Mouse Remote Control as the PC ENGLISH The remote control of this projector can be used as the PC mouse (wireless mouse function) by connecting the MOUSE connector of this projector and the PC. Remote control mouse functions · The cursor key on the remote control operates the computer mouse functions. · If a computer running Windows is connected, the ENTER button on the remote control operates as the computer mouse left click button and the CANCEL button as the computer mouse right click button. · If a Macintosh computer is connected, the ENTER and CANCEL buttons operate in the same way MOUSE button as the computer mouse click button. MOUSE MENU VIDEO CANCEL POWER RGB Connecting a PC and the MOUSE connector of this projector Before connecting a PC · Before connecting, turn off the PC power. Turn off the power of this projector if it is on. · When connection is completed, turn on the power of this projector and then start the PC. USB Port Connection Connect the supplied USB mouse cable directly to the USB port (universal serial bus) of the personal computer, as shown in the diagram. Personal computer USB port IBM PC/AT or Macintosh MOUSE connector USB mouse cable (accessory) AUDIO MOUSE RGB / YCbCr S-VIDEO VIDEO To PS/2 MOUSE port IBM PS/2 compatible PS/2 mouse cable (accessory) IBM PS/2 Mouse Port Connection Connect the supplied PS/2 mouse cable to the personal computer, as shown in the diagram. Note · Depending on the personal computer, the mouse may not be recognized in some cases if not connected to the MOUSE connector before the personal computer power is turned on. · In the case of some notebook and laptop type personal computers, it may not be possible to use the standard pointing device (track ball, etc. ) of the personal computer when connected to the MOUSE connector. In such case, it will not be possible to use the pointing device until the personal computer is rebooted, even if disconnected from the MOUSE connector. E ­ 17 Various functions FREEZE button AUTO button ZOOM +/­ button AUTO while using the unit The following operations can be performed by opening the FLIP COVER of the remote control. FREEZE MUTE MUTE button VOLUME +/­ button KEYSTONE +/­ button ZOOM KEYSTONE VOLUME Automatic Screen Adjustment Press the AUTO button. AUTO Adjusting the Volume Adjusting the volume of the unit's speaker. Press VOLUME + to increase the volume or ­ to decrease. VOLUME The position and size of the input image will be adjusted automatically in accordance with the resolution. Note Operation is the same as with the AUTO button of the main unit. KEYSTONE Adjustment Freezing animated images You can capture the desired frame of a moving picture. Press FREEZE button. A still image of the current frame is displayed. To restore the present picture, press the button again. FREEZE When distortion of the projected image cannot be compensated with the adjusters, press the KEYSTONE +/­ button to adjust accurately. KEYSTONE Tip The still picture can also be enlarged (see page 19). Turning off the image and muting the sound temporarily Press MUTE button. The image turns off and the sound is muted at the same time. To restore the picture and sound, press the button again. Using KEYSTONE button to adjust the top and bottom of a projected image. The top and bottom of the projected will be compensated, as shown in the diagram. [. . . ] · The unit was turned on immediately after being turned off. Turn off the unit, wait at least one minute, then turn on the unit again. (See page 33. ) E ­ 32 Replacing the lamp cartridge ENGLISH Lamp Cover Lamp cartridge The rated lamp life is about 1, 000 hours. The rated lamp life is the average life of the lamps produced and tested (under the test conditions of our company) for a long term, however, it may become shorter depending on the conditions of usage. [. . . ]