User manual MITSUBISHI M700V SPECIFICATIONS MANUAL

[. . . ] MELDAS and MELSEC are registered trademarks of Mitsubishi Electric Corporation. Microsoft®and Windows®are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Intel®, Pentium® and Celeron® are either trademarks or registered trademarks of Intel Corporation and its subsidiaries in the United States and other countries. Other company and product names that appear in this manual are trademarks or registered trademarks of the respective company. Introduction This manual describes the specifications of MITSUBISHI CNC M700V Series. [. . . ] (Arbitrary feed based on the PLC is also possible. ) (a) (i) X (b) (c) Y Z (o) (j) MDI (d) (p) (e) (k) (l) (g) (c) X Y Z (f) (n) (m) (a) Axis switching (b) Automatic operation (c) Axis control (d) X-axis position control (e) Y-axis position control (f) Z-axis position control (g) Manual operation (i) Tape (j) Memory (k) Jog (l) Handle (m) Return (n) Manual mode (o) Automatic mode (p) Simultaneous manual and automatic operation The feed rates for the axes subject to automatic commands and the feed rates for axes subject to manual command are set separately. The acceleration/deceleration modes (rapid traverse, cutting feed) are also set separately. Rapid traverse override, cutting feed override and second cutting feed override are valid both for axes subject to automatic commands and manual commands. Override cancel is valid for axes subject to automatic commands. Manual interlock is applied to axes subject to manual commands; automatic interlock is applied to axes subject to automatic commands. III - 199 MITSUBISHI CNC III Functional Specifications 11. 4. 10 Simultaneous Operation of JOG and Handle Modes M720VW M system L system M730VW M750VW M720VS M730VS M750VS When executing the jog feed and handle feed, both these feeds are available without changing the mode each time by inputting the jog mode signal and simultaneous operation of jog and handle modes signal to the control unit. However, while axis is moving in one of the two modes, the feed in the other mode is not valid. 11. 4. 11 Reference Position Retract M720VW M system L system M730VW M750VW M720VS M730VS M750VS When the retract signal is turned ON during the automatic and manual operation, this function can retract the tool immediately to a set reference position. The reference position to be retracted to can be selected from the 1st reference position to 4th reference position with 2-bit input signal. Set the retracting order of axes with parameter. (1) Other operations (a) When the retract signal is turned ON, the control unit is reset, the operation is interrupted, and the machining program is indexed. (b) When the rapid traverse input signal is input, the rapid traverse rate is applied. When the rapid traverse input signal is not input, the manual feed rate is applied. (c) If the retract signal is input during execution of a tapping cycle, the operation will be the tapping retract, and the normal reference position retract will be executed from the end point of tapping retract operation. (d) Even if the retract signal is input during the thread cutting cycle, it will be invalid. However, if the retract signal is input in a block other than the thread cutting block, the retracting operation will be executed. (e) If the retract signal is turned OFF midway during retracting, the operation will decelerate and stop. However, since the machining program is indexed, the block can not be resumed. (f) The retract signal is invalid if the coordinate system is not established. An operation error will occur when the retract signal is input in such case. III - 200 M700V Series Specifications Manual 11 Operation Support Functions 11. 4. 12 Tool Escape and Return M720VW M system L system M730VW M750VW M720VS M730VS M750VS Even if the machining program's operation is halted and the tool is escaped to change the tool or check the workpiece, etc. , the tool can be returned to the halted point (machining halted point) and machining resumed. After the machining program is halted, the halt point is designated, and the tool is escaped manually. The transit points for returning are designated when escaping. When returning, the tool passes through the transit points designated when escaping and returns to the halt point. Then, machining restarts. (a) (b) d (g) e e #2 #1 #1 d #2 (e) (d) (c) d a, b, c (f) a. [. . . ] FAMAS IS MERKEZI A BLOK No. 43 KAT 2 80270 OKMEYDANI ISTANBUL, TURKEY TEL: +90-212-320-1640 / FAX: +90-212-320-1649 Czech Republic Service Center TECHNOLOGICKA 374/6, 708 00 OSTRAVA-PUSTKOVEC, CZECH REPUBLIC TEL: +420-59-5691-185 / FAX: +420-59-5691-199 Russia Service Center 213, B. NOVODMITROVSKAYA STR. , 14/2, 127015 MOSCOW, RUSSIA TEL: +7-495-748-0191 / FAX: +7-495-748-0192 Sweden Service Center STRANDKULLEN, 718 91 FROVI, SWEDEN TEL: +46-581-700-20 / FAX: +46-581-700-75 Bulgaria Service Center 4 A. LYAPCHEV BOUL. , 1756 - SOFIA, BULGARIA TEL: +359-2-8176000 / FAX: +359-2-9744061 Ukraine (Kharkov) Service Center APTEKARSKIY PEREULOK 9-A, OFFICE 3, 61001 KHARKOV, UKRAINE TEL: +38-57-732-7744 / FAX: +38-57-731-8721 Ukraine (Kiev) Service Center 4-B, M. RASKOVOYI STR. , 02660 KIEV, UKRAINE TEL: +38-044-494-3355 / FAX: +38-044-494-3366 Belarus Service Center 703, OKTYABRSKAYA STR. , 16/5, 220030 MINSK, BELARUS TEL: +375-17-210-4626 / FAX: +375-17-227-5830 ASEAN MITSUBISHI ELECTRIC ASIA PTE. (ASEAN FA CENTER) Singapore Service Center 307 ALEXANDRA ROAD #05-01/02 MITSUBISHI ELECTRIC BUILDING SINGAPORE 159943 TEL: +65-6473-2308 / FAX: +65-6476-7439 Indonesia Service Center WISMA NUSANTARA 14TH FLOOR JL. [. . . ]