User manual MITSUBISHI MDT651S

[. . . ] 64. 5" LCD Display Monitor MODEL Before use - Please be sure to read the "Safety Precautions. " They are important to use this LCD display monitor. - Please check the content of the package. This document contains instructions for World Wide model and Japan model, but their accessories are different. English Deutsch Español Français Italiano Italiano Français Español Deutsch English Index Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . English-2 Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 2) Connection to multiple monitors Computer USB cable (commercially available) CAT5 cable (commercially available) CAT5 Tx BOX (accessory) Monitor (first monitor) Signal cable (Mini D-SUB 15-pin to Mini D-SUB 15-pin) (accessory) CAT5 cable (commercially available) Monitor (second monitor) 1. In addition to the connection described in 2-1), connect the OUT connector of the RGB5/CAT5 input/output connector (Modular connector 8-pin) of the first monitor and the IN connector of the RGB5/CAT5 input/output connector (Modular connector 8-pin) of the second monitor using a commercially available CAT5 cable. Connect the third and later monitors in the same way. You can connect up to 5 monitors. English-23 English CAT5 for long-distance connection or multiple-monitor connection 2. Connection of the CAT5 video connection function P-5 Connecting CAT5 (continued) Max. cable length/signal timing 150 m / 1920 x 1080 @60 Hz 200 m / 1920 x 1080 @60 Hz (Total length of the connected cables) Carry out as necessary Allowable cable length Connection One monitor Multiple monitors The lengths given above are based on the actual measurements using our standard signal source and the recommended cable as follows. Before installation, check the monitor operation in advance by connecting it with your computer and cables. Recommended cable: 8-pin modular connector, straight-through, shielded, Category 5 or 5e 3. Various settings involved in the CAT5 video connection In the case of the CAT5 video connection, configure the following settings displayed on the OSD screen. (See page 47. ) 1) CAT5 CABLE LENGTH Select the cable length, and the defaults of all the adjustment values are automatically determined. Select the length that is closest to the actual length of your cable. Make adjustment so that blur and smear of the displayed letters and graphic objects are minimized. 3) CAT5 RED GAIN/GREEN GAIN/BLUE GAIN When the displayed image is dark, increase each value. When whites aren't displayed as intended, adjust the RED GAIN and BLUE GAIN values. 4) CAT5 RED SKEW/GREEN SKEW/BLUE SKEW Adjust each value so that the color deviation in the displayed letters and graphic objects is minimized. English-24 P-6 Connecting RS-232C Monitor control via RS-232C Carry out as necessary · · Power ON or OFF Switching between input signals Connection Connection by RS-232C (For RS-232C cable (commercially available), the reverse type cable should be used. ) Rear of LCD monitor (first monitor) Rear of LCD monitor (second monitor) Computer (RS-232C connection) RS-232C OUT RS-232C OUT RS-232C RS-232C IN RS-232C IN RS-232C cable RS-232C cable · · Before making connections, turn off the personal computer and the monitors. Start the personal computer first, and then turn on the monitors. (Otherwise, the com port may be unusable. ) CAUTION: Never connect network devices to the CAT5 IN and OUT connectors. If you do so, they may adversely affect with each other, causing breakdown. NOTE: If your PC (IBM or IBM compatible) is equipped only with a 25-pin serial port connector, a 25-pin serial port adapter is required. If you use RS-232C control and CAT5 video connection, please switch the input select switch on CAT5 Tx BOX (on page 12) to side "USB" when connecting with USB cable for power supply, or to side "RS232C" when connecting with an auxiliary DC power adapter. English-25 English By connecting multiple LCD monitors and a computer using RS-232C cables (commercially available) or CAT5 cables (commercially available), you can control the monitors from the computer via the supplied CAT5 Tx BOX for the following operations: P-7 Connecting LAN Monitor connection using LAN Carry out as necessary By connecting the monitor and the computer using a LAN cable (commercially available), you can control the following functions from the computer. · · Power ON or OFF Switching between input signals Computer (LAN connection) Rear of LCD monitor (first monitor) LAN LAN cable LAN hub LAN hub LAN cable LAN English-26 P-8 · · Connecting the power cord to the monitor Connecting the power source English The power outlet socket should be installed as near the equipment as possible and should be easily accessible. Fully insert the prongs into the power outlet socket. [. . . ] When the display mode is changed, the OSD Image Adjust settings may need to be re-adjusted. · Check the monitor and your display card with respect to the compatibility and recommended signal timings. · If the displayed text is garbled, change the video mode to the non-interlace mode and use 60 Hz refresh rate. Image of component signal is greenish · Check to see if the DVD/HD input connector is selected. [. . . ]