User manual MITSUBISHI P91DW

[. . . ] DIGITAL MONOCHROME PRINTER MODEL P91DW OPERATION MANUAL FUNC DOWN UP SET COPY GAMMA FEED OPEN THIS OPERATION MANUAL IS IMPORTANT TO YOU. PLEASE READ IT BEFORE USING YOUR DIGITAL MONOCHROME PRINTER. DIGITAL MONOCHROME PRINTER This digital monochrome printer complies with the requirements of the EC Directive 89/336/EEC, 73/23/EEC, 93/42/EEC and 93/68/EEC. The electro-magnetic susceptibility has been chosen at a level that gains proper operation in residential areas, on business and light industrial premises and on smallscale enterprises, inside as well as outside of the buildings. All places of operation are characterised by their connection to the public low voltage power supply system. WARNING: Use the AC power cord recommended as below and a parallel cable (Hewlett Packard C2951A, etc. ) so as not to interfere with radio and television reception. [. . . ] Immediately after the paper is replaced, 2-3 images may be printed with a blank part due to hand's dust or oil. Avoid a direct sunlight or a place near a heater, and store the paper in a place with 30°C ( 86°F) or lower temperature and 35-80% RH. 2 2 When the paper is rapidly transferred from a cool place to a hot place, a vapor or a dew is generated on the paper surface causing paper jam or degraded printing quality. A finger print or dust on the paper surface may degrade the printing quality. Note: Mitsubishi brand thermal paper is specially treated with an antistatic coating against thermal head damage caused by static-electricity discharge. Make sure to check the contents. 1 Open the top of the box. 2 Remove the cushion above the unit. 4 Unwrap the unit. FUNC DOWN UP SET GAMMA FEED COPY Accessories Thermal paper AC power cord Cleaning paper Operation manual Printer driver (1 floppy disk) 5 4 FEATURES AND FUNCTIONS Front Panel 1 2345 6 7 8 9 FUNC DOWN UP SET COPY GAMMA FEED B OPEN A Name 1 2 3 4 5 6 7 8 9 A B Function Turns on/off the power. Function mode changes whenever FUNC is pressed. Press to change the value in function mode. Press to change the value in function mode. Press to set each function value and curve. Displays stand-by, functions and error messages. Press for additional copies of the previous printout. Printed paper will come out through this slot. Opens the door. Reference page 14·15 15 15 15-17 13 12 11 - Power switch FUNC button DOWN button UP button SET button Indicator GAMMA button FEED button COPY button Print exit/Cutter Lever 6 Rear Panel C 1234 LOCK ON OFF PARALLEL DATA IN ON OFF 1234 OFF D E F POTENTIAL EQUALIZATION TERMINAL This is used to equalize the potential of the equipment connected to this unit. For details refer to the installation instruction of equipment to be connected. AC LINE Name C D E F Function Select special functions. Connects to the device equipped with parallel data interface such as personal computer. Connect the power cord to this terminal. Makes the connected equipment of potential equal. Reference page 10 10 20 - 22 - Mode switches PARALLEL data terminal Power terminal (AC LINE) Potential equalization terminal 7 5 INSTALLATION OF PAPER 3 Pull out the paper end. · Pull out the first 1520cm (6 in. - 9 in. ) of the paper to remove any slack in the roll. Moisture, fingerprints or dust on the paper surface may cause a noise at printing or deterioration in print quality. Set the paper in the following procedure to prevent adhesion of fingerprint or dust on the paper surface. 1 Open the door. OPEN · Switch the lever located on the left side to the "OPEN" position. The door opens. 4 Close the door. 2 Load the paper roll. ·Place the paper roll in the printer. 5 Cut the paper end. printing side cutter INCORRECT CORRECT Note: The printing surface is the outside. Place the paper with the thermosensitive side (printing side) up. When the paper roll is placed inversely, images can not be printed. · Cut the paper end with the cutter just like tearing off the paper. 8 When setting the paper, observe the following precautions to prevent paper jam. Do not use defective paper. [. . . ] Returns to "High" when PeriphAck becomes "High". High: data 1 Low: data 0 Information will be expressed for parallel data of every signal from bit No. 1 to No. 8. 2 3 4 5 6 7 8 9 10 11 20 21 22 23 24 25 26 27 28 29 DATA1(LSB) DATA2 DATA3 DATA4 DATA5 DATA6 DATA7 DATA8(MSB) PeriphClk PeriphAck PC/DP PC/DP PC/DP PC/DP PC/DP PC/DP PC/DP PC/DP PC/DP PC/DP Reverse data transfer : Sends "Low" data when HostAck is "Low". Returns to "High" when HostAck becomes "High". Forward data transfer: High: DP is on BUSY status. [. . . ]