User manual MITSUBISHI PEFY-12

[. . . ] 5 1. 2. 2 Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1. 3 Working Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1. 3. 1 Kiosk Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1. 3. 2 Operator Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] In the center area is possible to check the cutting area of the layout rectangle. In order to fit better the picture inside every frame or rectangle, sometimes is better to rotate the picture. After pressing the "Finish order" button, a pop-up will appear in order to determine the amount of copies desired 28/84 Operator users manual 3. 7 Photo ID (Optional) Its highly recommended to follow the next steps to make an ID service. 3. 7. 1 Taking the pictures Before selecting the PhotoID service at the main screen, the operator should take the pictures to the customer. When using a digital camera with an USB cable connected to easyphoto: If an USB switch is being used between the camera and the easyphoto, this must be switched to the position where the connection between both devices is disabled, in order to allow the camera to take pictures. When an USB switch is not being used, the digital camera USB cable should be disconnected from the easyphoto. NOTE The behaviour of the camera when the USB cable is connected or disconnected may vary depending on the camera brand/model used. Also, the use of an USB switch is not always necessary. Please ask for more information to your dealer or installer. 3. 7. 2 Selecting the service Once the "Photo ID" button (in operator mode) is pressed, or the hidden area between language selection (flags) and prices is pressed, the Photo ID service is started. 29/84 Operator users manual 3. 7. 3 Selecting the picture source After this, depending on the system setup, its necessary to follow the source selection workflow or it can be avoided if the operator is using always the same digital picture files source (see the Administration and Settings chapter for more information). As instance, if the operator is using always the same digital camera connected through USB cable to the easyphoto, this can be indicated in settings and the application wont ask the operator where the pictures must be read from. It will search the pictures from the camera directly. There are several picture sources available: Digital Memory Card, USB memory device (both using the media card reader of the easyphoto system) and USB connection with digital cameras. In this case please make final adjustments manually. You can use several buttons to change: Rotation. The picture can be rotated in small amounts in both directions by pressing quickly the rotate button. To change the orientation of the picture (and changing the aspect ratio) to landscape or portrait, please keep pressed the rotate button for a couple of seconds. This is useful when a compatible USB camera (working as a mass storage device) is connected to the system and the photographer wants to stay working permanently in the PhotoID screen. By pressing the refresh button, the pictures are reloaded from the camera and the last picture taken is shown. Adjust the picture position to the biometric mask (when available) using the controls. For split layouts, use the group selector button at the top right of the screen before selecting the second picture to be included in current composition. Press "Finish order" each time you want to print a copy of current Photo ID composition. Press "Back" button to escape this screen. In this moment you will see the same screens explained in point 3. 4. 2. [. . . ] Power (yellow-LED) Error (red-LED) Push the "FEED" button in order that ERROR LED keeps flashing. Open the cover and press once the "FEED" button to confirm the change. The ticket printer LED starts to cycle slowly to confirm that the printer has been modified. Switch the ticket printer off and on again. If after doing this, the printer is working but the paper is not being cut, please add the following steps: 1. [. . . ]