User manual MITSUBISHI PEFY-54NMAU-E

[. . . ] 5 1. 2. 2 Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1. 3 Working Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1. 3. 1 Kiosk Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1. 3. 2 Operator Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Use the arrows to select the part of the image you want to crop. Press "Portrait/Landscape" buttons. Press the green tic to save the changes. Press the red cross to not save the changes and escape this screen. 3. 5 Burning DVD/CD Once the "DVD/CD burning" service button is pressed, the following screen is showed: Press "Burn all" button if you want to burn not only pictures but also all the files found in the original media. In this moment the screens explained from point 3. 4. 2 (Additional services: Would you like to burn a dvd or cd?) will be displayed. Press "Select photos" if you want to burn it with the selected pictures. 23/74 Operator users manual 3. 5. 1 Selecting photos Once the "Select photos" button is pressed, the following screen is showed: For selecting the images: 1. Use the arrows to display all the images. Press "Yes" to copy it and "No" to deselect it. Press "Back" button to escape this screen. Press "Finish order" to burn it. In this moment the screens explained from point 3. 4. 3 (Additional services: Would you like to add an indexprint?) will be displayed. When an USB switch is not being used, the digital camera USB cable should be connected to the easyphoto. When using a PTP camera, this will detect now the connection with the easyphoto system and will change to picture source mode. In most of the cameras using the Mass Storage mode, they have to be manually switched to this mode at this time. NEW 3. 7. 4 Selecting the layout Afterwards, the layout must be chosen. There are two kind of layouts, standard and split. Split layouts (using two different colours) allow mixing two different pictures. After choosing the layout, the Photo ID screen is shown. 28/74 Operator users manual 3. 7. 5 Selecting and working with the pictures In the top area, the pictures read from the source are shown. When selecting any of them, the picture will be loaded to be shown in the central area. In this screen, its also possible to change the layout by clicking on the preview placed on the top-right corner. The select layout screen will appear again to restart the workflow. 29/74 Operator users manual Once in the Photo ID screen again, its possible to select another picture. 3. 7. 6 Printing After pressing the "Print" button, a pop-up will appear in order to determine the amount of copies desired. When pressing the refresh button, the latest images from the picture source are reloaded. When using a camera with PTP connection, only the latest 8 images from the device are loaded. 30/74 Operator users manual 3. 7. 7 Automatic biometrics detection When automatic biometrics detection is active in the settings (see Administration chapter), it will take some more time and the picture could appear centred and zoomed. The easyphoto system is applying innovative imaging processing tools to detect the face of the customer and helping the operator of the system to center the picture in the biometrics mask shown in the centre of the screen. If a picture can not be correctly centred it appears a message under the picture just warning about it. The cause can be any of the following: The eyes of the customer are not clearly visible in the picture The top part of the head of the customer is too near the top egde of the picture. [. . . ] Open the cover and press once the "FEED" button to confirm the change. The ticket printer LED starts to cycle slowly to confirm that the printer has been modified. Switch the ticket printer off and on again. If after doing this, the printer is working but the paper is not being cut, please add the following steps: 1. [. . . ]