User manual MITSUBISHI PHOTO ID SYSTEM DIS 710

[. . . ] ID PHOTO SYSTEM DIS710E OPERATION MANUAL MONITOR ALARM MEMORY SHEET PRINT PAPER S-VIDEO POWER OPEN REMOTE CONTENTS Page 1 2 3 4 5 6 7 8 9 SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 5 UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 PRINTER SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 9 CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Insert the ink cassette with the knob side toward you until it is locked into place. · When taking the ink cassette out of the compartment, press the ink cassette locking holder to release the lock. 1 Push the printing unit until it is locked into place. 2 After plugging the power cord, press POWER button on the front panel. SET THE PRINTING UNIT 3 Press the MEMORY button for about 1 second while holding the MONITOR button on the front panel . · The print paper is automatically cut after sending by about 10cm. 4 Repeat 3 step. (Fingerprints and dust can be removed by feeding the print paper. The printing unit is initialized. ) 9 4. CONNECTION CABLE CONNECTION Connect the components as follows. (example) Make sure to turn off each device when connecting. "C"(image in the camera) or "P"(image in the printer) is shown on the LCD. C/P C Print the image. When printing the first image (with "P" mark, an image memorized in the printer), press PRINT button. PRINT When printing the second image (with "C" mark, an image memorized in the camera), press MEM button first, then, press PRINT button. Printed image MEM PRINT Printed image 7. When printing only one image (not multiple picture), skip the step Refer to page 14 to get maximum quality of your pictures. 13 6. PICTURE QUALITY ADJUSTMENT ADJUSTING PICTURE QUALITY To adjust the image source first is the key to get maximum picture quality. Relation Distance for taking picture, Guide No. , F number Distance (m) 1 1. 5 2. 5 2 F IRIS F IRIS F IRIS F IRIS 12 8 -17 14 5. 6 13 11 -20 8 -17 16 16 -24 18 20 8 -17 11 -20 22 22 -28 16 -24 24 26 11 -20 Guide 28 30 No. 32 32 -30 22 -28 16 -24 34 36 38 40 16 -24 42 44 22 -28 46 48 32 -30 50 52 54 22 -28 56 2 CAMERA ADJUSTMENT Always adjust the camera setting first. Only after you are sure that the camera is providing the best picture quality and color balance, adjust the printer setting. Make sure to adjust the camera setting in the same condition which you actually take a picture. For Iris setting, see the table shown right. 2 ADJUSTING THE BRIGHTNESS OF IMAGE (IRIS) 1 Press SHOT button to take a picture. 2 Press IRIS button. IRIS adjustment mode is selected. SHOT MANUAL 0 3 Press UP or DOWN button to select MANUAL. 4 Press SET button. IRIS The set value is flashing. Change the set value with UP or DOWN button. If the image is too dark, set the larger value. If the image is too light, set the smaller value. MANUAL -20 Too dark Good Too light 5 Press SET button. 6 Press ZOOM button to finish the iris setting menu. 14 7 Press SHOT button to take a picture. Check the brightness of image. If the brightness is not improved, repeat the steps get the best setting. 2 to 6 to 2 ADJUSTING THE COLOR OF IMAGE (WHITE BALANCE) 1 Place a piece of white paper in front of the camera and display it to cover the LCD. Place a white paper at the actual position of a person who is taking a picture from the camera. NOTE Do not display the picture with non-white objects when adjusting white balance. Adjust white balance under suficient lignt. [. . . ] Causes No power Countermeasures · Is the power cord plug disconnected from the outlet?Connect the power cord plug to the outlet firmly. · Are the camera, printer and connection box turned on?· Is the cable connected correctly? [. . . ]