User manual MITSUBISHI S290U

[. . . ] LCD Projector User Manual S290 MODEL S290U EN ­ 1 ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. WARNING Use the attached specified power supply cord. If you use another power-supply cord, it may cause interference with radio and television reception. [. . . ] The sharpness becomes TINT 0 sharper as the number increases. (It can not be changed COLOR 0 on XGA resolution. ) TINT . . . . . . . . . . . . . . . . . . . . The color balance of the image shifts green as the number increases and shifts to purple as the number decreases (displays only when the source is selected to VIDEO). Adjusts the color intensity of the image (displays only when the source is selected to VIDEO). Opt 2 AUDIO BASS . . . . . . . . . . . . . . . . . . . Use to select the audio output in the PinP mode, or (Sub). Opt AUDIO (Main) BASS TREBLE PinP AUDIO 1 1 / 3 INSTALLATION IMAGE REVERSE Use to reverse or invert the projected image. (Mirror invert) is effective INSTALLATION IMAGE REVERSE R when the projector is ceiling-mounted. Adjusts keystone correction of the image. If the image has AUTO POWER ON ON keystone distortion, select the approximate setting. For AUTO POWER OFF 0 min normal use, select 0°. TEST TEST SIGNAL ON OFF AUTO POWER ON . . . . . To select whether to boot up automatically when the power is turned on external to the projector. In this case, the main power switch of the projector has to be ON. Set this when the projector is hanging on the ceiling. · The projector is in stand-by mode when the lamp is not on. In this case, use the remote control to turn on the lamp. Use to select the length of time before projector switches to stand-by when there is no input signal selected source. Use to display the built-in test patterns on the screen. · The display will disappear when the setting is OFF or when you press any button except MENU, { , }, STILL, LASER, mouse pointer or R/L-click. Opt 4 OPTION MENU POSITION . Use to select the position where the menu is displayed, OPTION (upper left) or (lower right). Use to display the mode display on the screen. Use to display the splash screen on the screen when the SPLASH SCREEN ON power is turned ON. When AUTO is set, the video signal is processed ? [. . . ] · Install the projector far away from other equipment. · Turn on the monitor. · Press the reset button on the Terminal board. See page 15. EN ­ 24 Indicators The projector has three indicators each of which shows the working condition of the projector. The following offers solutions to possible problems. If a problem persists, turn the projector off and consult your dealer. POWER indicator LAMP indicator TEMP indicator LAMP ZOOM/ FOCUS TEMP VOLUME COMPUTER VIDEO MENU ENTER AUTO POSITION MUTE Normal condition POWER LAMP TEMP Steady red CONDITION Stand-by Lamp stand-by (about for 1 minute) The POWER is ON. [. . . ]