User manual MITSUBISHI SD206

[. . . ] N DATA PROJECTOR MODEL SD206U User Manual This User Manual is important to you. Please read it before using your projector. ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of suffcient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. WARNING Use the attached specified power supply cord. If you use another power supply cord, it may cause interference with radio and television reception. Use the attached RGB cable with this equipment so as to keep interference within the limit of an FCC Class B device. [. . . ] When changing ON/OFF, this setting is saved after cooling INSTALLATION down. (In case of Instant Shut Down, this setting is not AUTO POWER ON OFF saved. ) Choose ON when using the projector mounted AUTO POWER OFF OFF on the ceiling. ON SPLASH SCREEN · The projector is in the stand-by mode when the lamp BACK COLOR BLUE is off. Use the remote control to turn on the lamp. STANDARD LAMP MODE AUTO POWER OFF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Use to set the time elapsed before the projector enters the stand-by mode when there is no signal input from the IMAGE REVERSE OFF source. LAMP TIME 0 SPLASH SCREEN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Choose ON to display the splash screen when the power is turned on. BACK COLOR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Use to select the background from among BLUE and BLACK, which will be displayed when there is no signal input from the source. LAMP MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Use to change the brightness of the lamp. When LOW is chosen, the lamp brightness is kept low and the projector operating noise is reduced, resulting in a longer lamp replacement interval. · When the lamp mode is switched, the projected image may flicker. · Do not change the setting of LAMP MODE frequently. · When LAMP MODE has been set to LOW, the lamp mode changes from STANDARD to LOW about one minute after turn on. IMAGE REVERSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Use to reverse the projected image. Select MIRROR for rear projection with the tabletop-mounted projector. Select MIRROR INVERT for front projection with the ceiling-mounted projector. LAMP TIME. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The duration of illumination of a lamp converted in the Low mode is displayed. ON EN-16 3 FEATURE MENU POSITION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Use to select the position of the menu on the screen, opt. CINEMA MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . When AUTO is selected, the film mode will be automatiFEATURE cally activated when a film source signal is inputted. MENU POSITION When OFF is selected, the film mode will not be actiCINEMA MODE AUTO vated. ANAMORPHIC OFF ANAMORPHIC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Select ON when playing DVD discs containing data of PASSWORD MENU ACCESS widescreen images. [. . . ] Set COMPUTER INPUT in the SIGNAL menu to RGB when inputting the HDTV signal as RGB signal. · · · · TV60 and TV50 are equivalent to 480I and 576I respectively. When these signals are supplied to the VIDEO or S-VIDEO signal, the signal mode is indicated as TV60 or TV50. When they are supplied to the COMPONENT terminal, the signal mode is indicated as 480I or 576I. MONITOR OUT terminal is not available for SYNC on G (Green) signal. The component signal is only available for an output connector for 3-line fitting. [. . . ]