User manual MITSUBISHI SL1U

[. . . ] LCD Projector User Manual SL1 MODEL SL1U EN ­ 1 ESPAÑOL ITALIANO DEUTSCH FRANÇAIS ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. WARNING Use the attached specified power supply cord. If you use another power-supply cord, it may cause interference with radio and television reception. [. . . ] Select COMPUTER VIDEO mode to always output the sound which is inputted to the audio input terminal. Select MUTE not to output the sound at all. opt. XGA60 1. COMPUTER VIDEO AUTO OFF English OK FEATURE MENU POSITION A A EXPAND MODE AUDIO MODE ? VIDEO SIGNAL ANAMORPHIC AË LANGUAGE RESET ALL EN ­ 16 4 SIGNAL MEMORY CALL . . . . . . . . Use to adjust the horizontal position of the image. Use to adjust the vertical position of the image. Use to synchronize the projector with PC input signals so that the image is not blurred. Use to avoid image noise such as wide stripes. The unit adjusts itself automatically when connected to a DVD player with a component video output (Y, CB, CR). In the case the projector is connected to equipment that includes RGB output terminal, adjust to RGB mode. Adjusts the image when flagging occurs near the top of the screen. opt. XGA60 AUTO 0 0 0 0 RGB AUTO SIGNAL A U MEMORY CALL HORIZ. TRACKING RGB RGB COMPUTER INPUT HOLD USER MEMORIZE DELETE DEFAULT 5 SIGNAL - USER (Normally, there is no need for adjustments. ) CLAMP POSITION/ CLAMP WIDTH . . . . . . . . . If you use something similar, the brighter colors of the SIGNAL-USER projected image may become blurred. In this case, adjust CLAMP POSITION CLAMP POSITION or CLAMP WIDTH. LINES pixels of the input signal for normal setting. ) VERT. The image size grows higher as the number increases. (Adjust to the vertical lines SHUTTER(U) SHUTTER(L) of the input signal for normal setting. ) VERT. SYNC. Use to adjust the image when its motion does not run SHUTTER(LS) SHUTTER(RS) smoothly. Use to adjust the image when the noise etc. Use to adjust the image when the noise etc. Use to adjust the image when the noise etc. Use to adjust the image when the noise etc. appears on right side of image. 0 0 0 0 AUTO 0 0 0 0 User memory for signal setting This projector can memorize the maximum of 2 signal menu settings. [. . . ] It may not operate when changing the signal. Operation POWER ON POWER OFF INPUT COMPUTER INPUT VIDEO INPUT S-VIDEO ASCII !" _r1 _v1 _v2 HEX 21h 22h 5Fh 72h 5Fh 76h 5Fh 76h 31h 31h 32h · POWER OFF command will not work for 1 minute after the power is turned on. · POWER ON command will not work for 1 minute after the power is turned off. [Example] Set the input signal to COMPUTER (' 'is for ASCII code) Sending commands from the PC etc. [. . . ]