User manual MITSUBISHI SL25U

[. . . ] LCD Projector User Manual XL30 XL25 SL25 MODEL XL30U/XL25U/SL25U EN ­ 1 ESPAÑOL ITALIANO DEUTSCH FRANÇAIS ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. WARNING Use the attached specified power supply cord. If you use another power-supply cord, it may cause interference with radio and television reception. [. . . ] Select ON normally. opt. FEATURE MENU POSITION 1. AUTO OFF OFF ON English OK A A A A EXPAND MODE FRAME POSI. VIDEO SIGNAL SCART INPUT ANAMORPHIC 3D CineView ? AË LANGUAGE RESET ALL · · · · · · · LANGUAGE . . . . . . . . Use to select the language used in the menus. ( / English / Español / Deutsch / Français / Italiano / / / ) / RESET ALL . . . . . . . . . Use to reset the MENU settings (except LANGUAGE). When SCART is set to ON, nothing is output to the external monitor. When SCART is set to ON, normal computer signals are not projected. Use SCART-BNC (or SCART-Mini D-SUB 15P) cable (option), when connecting with AV device equipped with the SCART terminal. Some AV devices equipped with the SCART terminal may not be compatible with the projector. When VIDEO SIGNAL is set to AUTO, the image may not be projected with correct colors. Change the setting of VIDEO SIGNAL depending on the input signal in such cases. When 3D Cine View is switched from OFF to ON, you can check the motion detection operation about three seconds. The buttons on the remote control don't work during this period, which isn't a failure. When the LANGUAGE in FEATURE menu is set to English and NTSC video format is selected, the brightness is decreased 15 points by set-up cancel function for U. S. (The indicated value is not changed. ) The image becomes darker, but this is not a failure of the projector. opt. 4 SIGNAL MEMORY CALL . . . . . . . . . . Use to adjust the horizontal position of the image. Use to adjust the vertical position of the image. Use to synchronize the projector with PC input signals so that the image is not blurred. Use to avoid image noise such as wide stripes. The unit adjusts itself automatically when connected to a DVD player with a component video output (Y, CB, CR). In the case the projector is connected to equipment that includes RGB output terminal, adjust to RGB mode. [. . . ] The value will vary depending on the installation conditions, etc. ) ITEM KEYSTONE ASCII KS HEX 4Bh 53h VALUE ±30 How to set the grade Use the ASCII codes to set the grade for setting data. Please refer to the table below for the HEX code. ASCII HEX '+' 2Bh '­' 2Dh '0' 30h '1' 31h '2' 32h '3' 33h '4' 34h '5' 35h '6' 36h '7' 37h '8' 38h '9' 39h 7) Mute commands (Not executable in stand-by mode or while the Splash screen is projected. ) The mute commands are used for the mute setting of this projector with the 0(30h) and 1(31h). ITEM MUTE ASCII MUTE HEX 4Dh 55h 54h 45h VALUE 0 (OFF), 1 (ON) 8) Remote commands Some remote control operations can be achieved by the remote command codes. The remote commands have no data codes. Button's name on remote + VOLUME ­ VOLUME KEYSTONE EXPAND PinP MUTE { } $ % MENU ENTER AUTO POSITION STILL 16 : 9 ASCII r06 r07 r43 r02 r04 ra6 r53 r2b r4f r59 r54 r10 r09 ra4 re2 HEX 72h 72h 72h 72h 72h 72h 72h 72h 72h 72h 72h 72h 72h 72h 72h 30h 30h 34h 30h 30h 61h 35h 32h 34h 35h 35h 31h 30h 61h 65h 36h 37h 33h 32h 34h 36h 33h 62h 66h 39h 34h 30h 39h 34h 32h [Example] When displaying the MENU selection bar (Figures and symbols enclosed in quotation marks are ASCII codes. ): Sending commands from the PC, etc. [. . . ]