User manual MITSUBISHI WD500U-ST

[. . . ] EN DATA PROJECTOR MODEL WD510U/WD510U-G User Manual This User Manual is important to you. Please read it before using your projector. ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. WARNING Use the attached specified power supply cord. If you use another power supply cord, it may cause interference with radio and television reception. [. . . ] Note that you cannot use some AV devices equipped with the SCART terminal to connect with this projector. EN-20 Menu operation (continued) 4. TRACKING Setting 0-999 0-999 0-31 0-2800 AUTO RGB COMPUTER INPUT YCBCR/YPBPR OVER SCAN HOLD USER CLAMP POSITION CLAMP WIDTH VERT. SYNC LPF SHUTTER(U) SHUTTER(L) SHUTTER(LS) SHUTTER(RS) 1-255 1-63 AUTO / OFF ON / OFF 0-20 0-20 0-20 0-20 Use this setting to correct solid white or solid black that appears in projected images Use this setting to correct solid black that appears in projected images. Use this setting to adjust projected images when the motion is not smooth. Select this setting to enable or disable LPF. Use this setting to adjust projected images when noise appears in the top part of the image. Use this setting to adjust projected images when noise appears in the bottom part of the image. Use this setting to adjust projected images when noise appears in the left half of the image. Use this setting to adjust projected images when noise appears in the right half of the image. ? 100%-90% OFF / ON Feature description Select this setting to adjust the horizontal position of projected images. Select this setting to adjust the vertical position of projected images. Select this setting to eliminate flickering or blurs, if they appear, when you are viewing projected images. Select this setting to eliminate vertical wide stripes, if they appear, when you are viewing projected images. Automatically sets the appropriate setting. Select this setting when you connect the projector to high definition video equipment having R, G, and B output terminals. Select this setting when you connect the projector to a DVD player or other device having Y, CB, and CR (or Y, PB, and PR) component video output terminals. Use this setting to adjust the display area of projected images. Use this setting to adjust projected images when flagging occurs in the upper area of the screen. opt. SIGNAL HORIZ. TRACKING RGB RGB 0 0 0 0 RGB 100% OFF OK COMPUTER INPUT OVER SCAN HOLD USER opt. SIGNAL USER CLAMP POSITION CLAMP WIDTH VERT. SYNC LPF SHUTTER(U) SHUTTER(L) SHUTTER(LS) SHUTTER(RS) 1 1 AUTO OFF 0 0 0 0 SIGNAL USER menu · · · · · · Horizontal strips may appear in the enlarged projected image, though these conditions are not a malfunction. When you change the value of the horizontal or vertical position drastically, noise may appear. The adjustable range of the vertical position varies depending on the type of the input signal. The image may be stationary even when the value is changed. SHUTTER does not work correctly during keystone adjustment. [. . . ] Images with SYNC on G (Green) signal may jitter. Images with SYNC on G (Green) signal may be tinged with green. If the resolution and frequency of your computer aren't shown on the table, find the compatible resolution and frequency by changing the resolution of your computer. Set COMPUTER INPUT in the SIGNAL menu to RGB when inputting the HDTV signal as RGB signal. · TV60 and TV50 are equivalent to 480i and 576i respectively. [. . . ]