User manual MITSUBISHI WD720U

[. . . ] DLP™ PROJECTOR MODEL XD700U WD720U User Manual XD700U WD720U This User Manual is important to you. Please read it before using your projector. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: CAUTION: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. [. . . ] When it occurs, press the AUTO POSITION button. (See page 18. ) When the signal is still not projected properly, adjust the projected image using the Signal menu. Simple method to adjust the image position To adjust the horizontal position: 1. Align the left edge of the image with the left side of the screen by adjusting H. Position. Then, align the right edge of the image with the right side of the screen by adjusting Tracking. 2. Repeat step 1 to complete the adjustment of the horizontal position. To adjust the vertical position: 3. Align the upper edge of the image with the upper side of the screen by adjusting V. Position. How to adjust the image supplied from the computer using the menu: Perform the following procedures when the following conditions occur. Adjust Tracking in the Signal menu. Adjust Fine sync in the Signal menu. When the projected image is displaced horizontally. Adjust H. Position in the Signal menu. Every time the  button is pressed, the image moves to the right. Every time the  button is pressed, the image moves to the left. When the projected image is displaced vertically. Adjust V. Position in the Signal menu. Every time the  button is pressed, the image moves down. Every time the  button is pressed, the image moves up. Change the setting of Hold in the Signal menu. To select On , press the ENTER button, and Adjust Begin or End to minimize the flagging. A solid black or solid white appears in the image. Adjust Clamp Position or Clamp Width in the Signal-User menu. Noise appears in the right or left half of the image. Adjust Shutter(LS) or Shutter(RS) in the SignalUser menu. Noise appears in the top or bottom part of the image. [. . . ] (See page 52. ) The lamp operation time exceeds the time elapsed until the lamp lifetime notice while the power is off. (See page 52. ) The lamp operation time exceeds the time elapsed until the lamp lifetime. (See page 52. ) The lamp cover isn’t closed. Steady red Blinking red Steady red Steady red Close the cover correctly. Blinking green/red Off Abnormal. Steady or Blinking green/red Blinking Contact your dealer. EN-57 Specifications Type Model Rated power supply Power consumption Display Technology Colors Projection lens Light source lamp Picture size PC compatibility DLP™ projector XD700U WD720U 100 - 240 V AC, 50/60 Hz 4. 1 A During standby: 0. 5W (when Standby Mode is Low) 0. 7-inch single chip Digital Micromirror 0. 65-inch single chip Digital Micromirror Device (DMD) Device (DMD) Pixels: 1024 x 768 = 786432 pixels Pixels: 1280 x 800 = 1024000 pixels 16770000 colors F 2. 4-2. 8, f = 20. 6-30. 1 mm 280 W 40 - 300 inch (Wide) (aspect ratio 4:3) 40–300 inch (Wide) (aspect ratio 16:10) Resolution: 640 x 480 (Expand) Resolution: 640 x 480 (Expand) 1024 x 768 (Real) 1280 x 800 (Real) 1600 x 1200 (Compress) 1600 x 1200 (Compress) Sync on Green available Sync on Green available NTSC/NTSC 4. 43/PAL (including PAL-M, N)/SECAM/PAL-60 Component Video (DVD/HDTV) (480i, 576i, 480p, 576p, 1080i, 720p, 1080p) 10 W mono x 1 Luminance signal: 1. 0 Vp-p 75 Ω (negative sync. ) Chroma signal: 0. 286 Vp-p 75 Ω (burst signal) 1. 0 Vp-p 75 Ω (negative sync. ) 350 mVrms, 10 kΩ or more RGB: 0. 7 Vp-p 75 Ω (negative sync. ) YPBPR/YCBCR: Y: 1. 0 Vp-p (negative sync. ) PBPR/CBCR: 0. 7 Vp-p HD/CS: TTL level (positive or negative) VD: TTL level (positive or negative) HDMI 19-pin HDMI interface (TMDS single link) (only PCM audio is supported) SERIAL terminal (RS-232C), LAN terminal (RJ-45) 345 x 134 x 270 mm (width x height x depth) Approx. 4. 1 kg 71 inch (1. 8 m) +41°F (+5°C) - +95°F (+35°C), 30 - 90% Video compatibility Speaker S-video input Video input Audio input Analog RGB input HDMI input Control connector Outside dimensions Weight Length of power cord Temperature, humidity (performance guaranteed) • The specifications and outside appearance of the projector are subject to change without prior notice. EN-58 Specifications (continued) Connectors COMPUTER/COMPONENT VIDEO IN, MONITOR OUT (mini D-SUB 15-pin) 11 6 1 5 15 10 HDMI (HDMI 19-pin) 1 19 2 18 COMPUTER/COMPONENT VIDEO IN Pin No. [. . . ]