User manual MITSUBISHI WL6700

[. . . ] LCD PROJECTOR MODEL WL6700U User Manual WL6700 This User Manual is important to you. Please read it before using your projector. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. WARNING Use the attached specified power supply cord. If you use another power supply cord, it may cause interference with radio and television reception. [. . . ] Use a commercially available SCART-Mini D-SUB 15-pin cable when connecting this projector with an AV device equipped with the SCART terminal. Some AV devices equipped with the SCART terminal aren't compatible with this projector. EN-26 Menu operation (continued) 4. SIGNAL menu opt. SIGNAL - RESOLUTION (MEMORIZE) menu opt. SIGNAL - USER menu opt. SIGNAL A U H V SIGNAL AUTO 1024x768 0 0 0 0 RGB 100% OFF OK SIGNAL USER 75. 04 Hz 60. 02 KHz 1024 768 OK OK ? MEMORY CALL RESOLUTION (MEMORIZE ) HORIZ. TRACKING RESOLUTION (MEMORIZE) VERTICAL FREQUENCY HORIZONTAL FREQUENCY HORIZ. LINES EXECUTE CANCEL CLAMP POSITION CLAMP WIDTH VERT. SYNC LPF SHUTTER(U) SHUTTER(L) SHUTTER(LS) SHUTTER(RS) 1 1 AUTO OFF 0 0 0 0 RGB RGB COMPUTER INPUT OVER SCAN HOLD USER ITEM MEMORY CALL SETTING AUTO / MEMORY 1 MEMORY 2 / FUNCTION Use to select the setting of RESOLUTION (MEMORIZE) already saved. Impossible to select if no setting has been saved. It optimizes the signal format automatically depending on the type of video signal supplied from the computer. Press the ENTER button to clear the setting already saved. To change the current setting, press the ENTER button to display the RESOLUTION (MEMORIZE) menu. The new setting can be saved to MEMORY 1 or MEMORY 2. The vertical frequency of the currently projected video signal is displayed. The horizontal frequency of the currently projected video signal is displayed. The number of horizontal pixels of the currently projected video signal is displayed. When you change the current setting, select EXECUTE, and then press the ENTER button, the image is automatically adjusted according to the resolution you set. The adjustment result can be saved to MEMORY 1 or MEMORY 2. The number of vertical pixels of the currently projected video signal is displayed. When you change the current setting, select EXECUTE, and then press the ENTER button, the image is automatically adjusted according to the resolution you set. The adjustment result can be saved to MEMORY 1 or MEMORY 2. Press the ENTER button to start the automatic adjustment. At the completion of the automatic adjustment, a message is displayed and you can save the adjustment result to MEMORY 1 or MEMORY 2. The process to change the current resolution is canceled and the SIGNAL menu is displayed. [. . . ] * : Composite Sync Connectors SERIAL (D-SUB 9-pin) 5 9 1 COMPUTER/COMPONENT VIDEO IN 2 (Mini D-SUB 15-pin) 5 10 6 15 11 1 Pin No. R(RED)/PR/CR G(GREEN)/Y B(BLUE)/PB/CB GND GND GND GND GND DDC 5V GND GND DDC Data HD/CS VD DDC Clock COMPUTER/COMPONENT VIDEO DVI-D (HDCP)(DVI-D 24-pin) 24 16 17 9 6 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 8 1 Pin No. 1 2 3 4 5 6 7 8 9 Name TXD RXD GND - I/O IN OUT - Pin No. TMDS DATA 2TMDS DATA 2+ TMDS DATA 2 Shield DDC Clock DDC Data TMDS DATA 1TMDS DATA 1+ TMDS DATA 1 Shield - Pin No. [. . . ]