User manual MITSUBISHI WL7050U

[. . . ] LCD PROJECTOR MODEL WL7050U User Manual WL7050 This User Manual is important to you. Please read it before using your projector. U CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: CAUTION: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. [. . . ] • The RESET ALL process may take some time to complete. EN-35 Menu operation (continued) SIGNAL menu opt. opt. SIGNAL A U H V SIGNAL AUTO 1024 x 768 0 0 0 0 AUTO 100% ON ENTER SIGNAL USER 60. 00 Hz 48. 36 KHz 1024 768 OK OK ? MEMORY CALL RESOLUTION (MEMORIZE ) HORIZ. TRACKING RESOLUTION (MEMORIZE) VERTICAL FREQUENCY HORIZONTAL FREQUENCY HORIZ. LINES EXECUTE CANCEL CLAMP POSITION CLAMP WIDTH VERT. LPF SHUTTER(U) SHUTTER(L) SHUTTER(LS) SHUTTER(RS) 1 1 AUTO OFF 0 0 0 0 R RG GB B COMPUTER INPUT OVER SCAN HOLD USER ITEM MEMORY CALL SETTING AUTO / MEMORY 1 MEMORY 2 ) 640-1920 / RESOLUTION (MEMORIZE VERTICAL FREQUENCY HORIZONTAL FREQUENCY HORIZ. LINES 350-1200 EXECUTE CANCEL OK OK 0-999 0-999 0-31 0-9999 AUTO RGB YCBCR/YPBPR HORIZ. TRACKING COMPUTER INPUT OVER SCAN HOLD USER CLAMP POSITION CLAMP WIDTH VERT. LPF SHUTTER(U) SHUTTER(L) SHUTTER(LS) SHUTTER(RS) 100%-90% OFF / ON ENTER 1-255 1-63 AUTO / OFF ON / OFF 0-38 0-38 0-63 0-63 FUNCTION Use to select the setting of RESOLUTION (MEMORIZE) already saved. Impossible to select if no setting has been saved. It optimizes the signal format automatically depending on the type of video signal supplied from the computer. Press the ENTER button to clear the setting already saved. To change the current setting, press the ENTER button to display the RESOLUTION (MEMORIZE) menu. The new setting can be saved to MEMORY 1 or MEMORY 2. The vertical frequency of the currently projected video signal is displayed. The horizontal frequency of the currently projected video signal is displayed. The number of horizontal pixels of the currently projected video signal is displayed. When you change the current setting, select EXECUTE, and then press the ENTER button, the image is automatically adjusted according to the resolution you set. The adjustment result can be saved to MEMORY 1 or MEMORY 2. The number of vertical lines of the currently projected video signal is displayed. When you change the current setting, select EXECUTE, and then press the ENTER button, the image is automatically adjusted according to the resolution you set. The adjustment result can be saved to MEMORY 1 or MEMORY 2. Press the ENTER button to start the automatic adjustment. [. . . ] It may not display images of higher resolutions than 1280 x 800 correctly. • Images with SYNC on G (Green) signal may jitter. • Images with SYNC on G (Green) signal may be tinged with green. • If the resolution and frequency of your computer aren’t shown on the table, find the compatible resolution and frequency by changing the resolution of your computer. [. . . ]