User manual MITSUBISHI WS-48513

[. . . ] Owner's Guide WS-48513, WS-48613, WS-55513, WS-55613, WS-55813, WS-65513, WS-65613, WS-65713, WS-65813, WS-73513, WS-73713 visit our website at Projection Television Models w w w. m i t s u b i s h i -t v. c o m CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user of the presence of uninsulated "dangerous voltage" within the product's enclosure that may be sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Warning: To avoid permanently imprinting a fixed image onto your TV screen, please do not display the same stationary images on the screen for more than 15% of your total TV viewing in one week. [. . . ] · INITIAL - Allows initial setup, in the event NetCommand setup was cancelled or if the entire configuration was deleted or not completed. Selecting the Icon Position screen allows you to arrange the device icon order on the Device Selection menu to your preferred sequence to make the operation of the TV easier. Press ADJUST , , , or to highlight the icon to be moved and then press ENT(er). Press ADJUST , , or to move the icon to the desired position and then press ENT(er) to secure the icon in the new position. Icon Position Language Display the on-screen menus in either English or Spanish (Español). The first time you powered On your TV, you were requested to select an on-screen menu language. If you choose to change the selection, all menu text will immediately switch to the language of your choice. 57 Antenna Menu: Antenna, Memorize Channels, Channel, Memory and Name Antenna Menu The following Antenna Menu options are available for use on Antenna A, Antenna B or Antenna DTV. You can memorize channels, add or delete channels, and add channels to an SQV (Super Quick ViewTM) list. For Antenna A and Anenna B, you can name channels. Antenna Menu Figure 9 Channel For additional Channel editing, press ADJUST or to select the channel or press CH or for channels already in memory. On Antenna DTV, when the broadcaster has sent a virtual channel number, the virtual channel number is shown in the text box and the original digital channel is shown below on-screen, as a reference. Select Antenna to perform the functions listed below. Figure 9. Antenna Menu Memorize For Antenna A or Antenna B Select either Air (when used with an indoor/outdoor antenna) or Cable (when used with direct cable) then press ENT(er) to start the automatic channel memorization process. For Antenna DTV Select Air when used with an indoor/outdoor antenna. Select Cable or Cable (HRC) when used with Direct cable. There are three types of Cable systems: Standard, IRC and HRC. To memorize Standard or IRC, select Cable; to memorize HRC, select Cable (HRC). Check with your Cable company to determine which type of Cable system they use. If your cable company cannot advise you, select Cable. To stop the automatic channel memorization process, press CANCEL. Channels memorized before you pressed CANCEL are retained in memory. After memorizing channels, the channels in the memory can be accessed in ascending or descending order or by pressing CH or . After the available channels have been memorized with Memorize, weaker channels viewed with Antenna A or Antenna B can be added. Unwanted channels for Antenna A, Antenna B, or Antenna DTV can also be deleted. Press CH or on the remote control to see the channels in memory. Press ADJUST or to select Added or Deleted for the channel shown in the Channel number box. Memory Channels shown on Antenna A or Antenna B can be named (up to four characters). After you enter a name, it will appear on the TV screen, next to the channel number. [. . . ] Some A/V Receivers will switch automatically to digital when a digital audio signal is supplied so you do not need to do anything. "Other" A/V Receivers can be manually switched by remote control, for these types of A/V Receivers, see the NetCommand Guide Appendix for NetCommand control of this features. Some A/V Receivers will require that you make this change on the front panel of the A/V Receiver. Q. The front panel of my A/V Receiver is too tall or too convex for the IR emitter signal to reach the remote control sensor of the A/V Receiver. [. . . ]