User manual MITSUBISHI WS-65413

[. . . ] Owner's Guide Projection Television Models WT-, WS-, WS- and WS- visit our website at RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER OR BACK. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user of the presence of uninsulated "dangerous voltage" within the product's enclosure that may be sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Warning: To avoid permanently imprinting a fixed image onto your TV screen, please do not display the same stationary images on the screen for more than 15% of your total TV viewing in one week. [. . . ] A/V Reset on the front control panel resets all inputs at one time. See pages - for more detailed setup information. ENTER for menu or to start MENU to return 34 Figure 8. Audio/Video Settings Menu SETUP Menu: Memorize Channels, Memorize Menu, Input Assignment (WT-) (Figure 9) Memorize Channels Select Memorize Channels for each antenna you use. The TV will find and remember strong channels and skip the unused or weaker channels. ENTER for menu or to start MENU to return DTV Note: If you have a DTV receiver connected, you will need to use that receiver's channel memorization system to memorize digital channels. Figure 9. Memorize Channels Menu (Figure 10) MEMORIZE Menu Stop memorization at any time by pressing CANCEL. Channels memorized prior to pressing CANCEL will stay in memory. After channels are memorized, you may select memorized channels in ascending or descending order by pressing the CHANNEL button on the remote control. ENTER for menu or to start MENU to return Figure 10. Memorize Menu (Figure 11) WT-42413 INPUT ASSIGNMENT Menu INPUT ASSIGNMENT turns off unused inputs, turns them on again or changes the name of the input. If you turn an input Off, it will be skipped when you press DEVICE on the remote control. Choices are: ANT-A, ANT-B: On or Off DTV: Y/Pb/Pr, RGB, RGBHV or Off COMPONENT Cycle through a list of preset names or Off INPUT-1, INPUT-2, INPUT-3: Cycle through a list of preset names or Off MonitorLink (MONLINK) Cycle through a list of preset names or Off ENTER for menu or to start MENU to return Figure 11. Input Assignment Menu WT-42413 35 (Figure 12) SETUP Menu: NetCommand® IR Setup, Language, IR Device Setup Menus (WS-, WS-, WS-) NetCommand IR Setup Menu For simple control with the Mitsubishi TV remote, select the NetCommand IR SETUP from the SETUP menu screen. There are basic steps to the NetCommand IR Setup: 1. Select the devices that are connected to the TV (Net Command IR Device Setup Menu) 2. Have the TV learn the device's remote control keys (NetCommand IR [Device] Learn menu) 3. Select or change the Input(s) the device(s) is (are) connected to (NetCommand IR Input Assignment Menu) (Figure 13) Language Figure 12. SETUP Menu, NetCommand® IR On initial set up, before you can use the NetCommand IR Menus, the language for the menu screens needs to be selected. Your choices are English or Spanish (Español). NOTE: This Language screen only appears on initial TV setup. To change the language later, select Language from the SETUP Menu screen (page ). NetCommand IR Menu (Figure 14) MENU to return (Figure 14) 1. NetCommand IR Device Setup Menu Select NetCommand IR to start the TV learning process. Figure 13. NetCommand® IR Menu, Language Using the Adjust buttons, select Yes for each device (AV Receiver, Cable, DTV, etc. . . ) you have connected to the TV. After selecting Yes, press ENTER to have the WS-, WS- or WS- go to the Learn menu to start learning the device. NOTE: If you connect a cable box with an RF output other than channel , please see the Channel Edit Menu on page . 36 Figure 14. [. . . ] Write down the back panel input connections and correctly match to the NetCommand IR Input Assignment menu (p. · To reset the factory default settings: . Press the MENU button followed by number buttons , , and on the remote control. Result: The above steps activate the Reset System Defaults menu screen . [. . . ]