User manual MITSUBISHI X120

[. . . ] LCD Projector User Manual X120 MODEL LVP-X120A 1 APPENDIX ESPAÑOL FRANÇAIS ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. WARNING Use the attached specified shielded power-supply cord. If you use another cord, it may cause interference with radio and television reception. Use the attached RGB cable, RS-232C cable with this equipment so as to keep interference within the limit of a Class A device. The projector automatically shuts off when the lamp is used up in about 2, 000 hours, and the projector will not turn on until lamp is replaced. DO NOT LOOK DIRECTLY INTO THE LENS WHEN PROJECTOR IS IN THE POWER ON MODE. 2 Contents Important safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Overview of the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Overview of the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Battery installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Important: · Some computers may not be compatible with the projector. · The projector's maximum resolution is 1, 024 768 pixel. It may not be displayed correctly for the pictures of higher resolutions than 1, 024 768. · The picture with a SYNC on G (Green) signal may jitter. · The picture with a SYNC on G (Green) signal may be tinged with green. · If the resolution and frequency of your computer are not shown on the table. , change the resolution of your computer. You may find the compatible resolution and frequency. · Set the RGB/Y, CB, CR in SIGNAL menu to RGB, when inputting the HDTV signal as RGB signal. 21 ENGLISH Advanced feature for presentation Expand By pressing the EXPAND button on the remote control, you can view the detailed image of the picture. Press the MENU button once to display the onscreen menu. Press the $ or % button to select PRESENTATION menu. Press the{ or } button to select ZOOM MODE or POSITION. Press the $ or % button to set the ZOOM MODE or POSITION. Press the MENU button twice to exit the menu system. ZOOM MODE (ZOOM MODE1) (ZOOM MODE2) Still How to stop the picture temporarily (still picture) 1. Press the STILL button on the remote control. Press the STILL button on the remote control again. · To release the still picture, any buttons also can be used. Normal picture Zooming picture Normal picture (ZOOM MODE3) Zooming picture (ZOOM MODE4) Zooming picture Actual size picture Using the Expand mode 1. A red frame indicating EXPAND area will appear. · You can magnify different areas of the active picture by pressing the {, }, $ or % button. · You can change the magnification of the zoomed area by pressing the + or - button. · Display enlargement does not work with video input or S-video input. · In EXPAND mode, do not display the test pattern. · The red frame indicating EXPAND area will disappear when the cursor is selected. Indication Mode 4 (actual size display) · Pressing the $, % buttons is for adjusting fine adjust. [. . . ] " _r1 _v1 _c1 HEX 21h 22h 5Fh 72h 5Fh 76h 5Fh 63h 31h 31h 31h · POWER OFF command will not work for 1 minute after the power is turned on. · POWER ON command will not work for 1 minute after the power is turned off. [Example] Set the input signal to RGB (' 'is for ASCII code) Sending commands from the PC etc. 30 30 5F 72 31 OD '0' '0' '_' 'r' '1' ' ' Status code from projector Meaning Command for setting the input signal to RGB Command received (Command echo back) 30 30 5F 72 31 OD '0' '0' '_' 'r' '1' ' ' 5) Remote commands The some remote control operation can be done by remote command codes. Button's name on remote + VOLUME ­ VOLUME EXPAND { } $ % MENU ENTER AUTO PLAY(PC CARD) RELEASE(PC CARD) AUTO POSITION STILL ASCII r06 r07 r02 r53 r2b r4f r59 r54 r10 r32 r22 r09 ra4 HEX 72h 72h 72h 72h 72h 72h 72h 72h 72h 72h 72h 72h 72h 30h 30h 30h 35h 32h 34h 35h 35h 31h 33h 32h 30h 61h 36h 37h 32h 33h 62h 66h 39h 34h 30h 32h 32h 39h 34h [Example] Display MENU selection bar. [. . . ]