User manual MITSUBISHI X390

[. . . ] LCD Projector User Manual X400B X390 MODEL LVP-X400BU / LVP-X390U EN ­ 1 ESPAÑOL ITALIANO DEUTSCH FRANÇAIS ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET MUST BE INSTALLED NEAR THE EQUIPMENT AND SHOULD BE EASILY ACCESSIBLE. WARNING Use the attached specified power supply cord. If you use another power-supply cord, it may cause interference with radio and television reception. [. . . ] Use to synchronize the projector with PC input signals so that the image is not blurred. Use to avoid image noise such as wide stripes. The unit adjusts itself automatically when connected to a DVD player with a component video output (Y, CB, CR). In the case the projector is connected to equipment that includes RGB output terminal, adjust to RGB mode. Adjusts the image when flagging occurs near the top of the screen. Opt XGA60 AUTO 0 0 0 0 RGB AUTO SIGNAL A U MEMORY CALL HORIZ. TRACKING RGB RGB COMPUTER INPUT HOLD USER MEMORIZE DELETE DEFAULT 5 SIGNAL - USER (Normally, there is no need for adjustments. ) CLAMP POSITION/ CLAMP WIDTH . . . . . . . . . If you use something similar, the brighter colors of the SIGNAL-USER projected image may become blurred. In this case, adjust CLAMP POSITION CLAMP POSITION or CLAMP WIDTH. LINES pixels of the input signal for normal setting. ) PLL VERT. LINES . . . . . . (Adjust to the vertical lines SHUTTER(U) of the input signal for normal setting. ) SHUTTER(L) PLL . . . . . . . . . . . . . . . . . . . . . . Use to adjust the image when skewed on top. Select AUTO for SHUTTER(LS) SHUTTER(RS) normal setting. Use to adjust the image when its motion does not run smoothly. Use to adjust the image when the noise etc. Use to adjust the image when the noise etc. Use to adjust the image when the noise etc. Use to adjust the image when the noise etc. appears on right side of image. 0 0 0 0 AUTO AUTO 0 0 0 0 User memory for signal setting This projector can memorize the maximum of 2 signal menu settings. Select MEMORIZE in the SIGNAL menu, and press the ENTER button. Press the $ or % button to select the memory which you wish to record (USER 1 or USER 2). Initialite the setting which has been changed (Default) Select RESET in the SIGNAL menu, and press the ENTER button. · When initializing, selection buttons will not work for about 2 - 18 seconds. Select the user setting Select MEMORY CALL in SIGNAL menu, and press the $ or % button to select the memory (USER 1 or USER 2). [. . . ] 30 30 21 0D '0' '0' '!' ' ' Status code from projector Meaning Command for POWER ON 30 30 21 0D '0' '0' '!' ' ' Command received (Command echo back) 4) Operation commands The operation commands execute the basic operation setting of this projector. It may not operate when changing the signal. Operation POWER ON POWER OFF INPUT COMPUTER 1 INPUT COMPUTER 2 INPUT VIDEO 1 INPUT VIDEO 2 ASCII !" _r1 _r2 _v1 _v2 HEX 21h 22h 5Fh 5Fh 5Fh 5Fh 72h 72h 76h 76h 31h 32h 31h 32h · POWER OFF command will not work for 1 minute after the power is turned on. · POWER ON command will not work for 1 minute after the power is turned off. [. . . ]