User manual MITSUBISHI XD200

[. . . ] DATA Projector User Manual X D200 SD200 MODEL XD200U / SD200U EN ­ 1 ESPAÑOL ITALIANO DEUTSCH FRANÇAIS ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. WARNING Use the attached specified power supply cord. If you use another power-supply cord, it may cause interference with radio and television reception. [. . . ] Use to select the modes of the high quality line doubler. Select 1 for the Cross Color Suppression mode. Select 3 for normal high quality line doubler mode. · Though square-shaped noise may appear in the projected image when 1 is selected, this is not failure. If it is obtrusive, select other positions than 1. · A playback signal on a deteriorated videotape or a poor-quality signal may not be projected properly. When projecting such a signal, change the setting of the Video mode and check the projection quality. Opt TV60 FEATURE MENU POSITION UPPER LEFT EXPAND 1 AUTO AUTO English OK A A EXPAND MODE VIDEO MODE CINEMA MODE ? VIDEO SIGNAL A Ë LANGUAGE RESET ALL EN ­ 16 CINEMA MODE . . When ON is selected, the film mode will be automatically activated when a film source signal is inputted. When OFF is selected, the film mode will not be activated. When AUTO is selected, the appropriate video format is automatically selected depending on the input signal. If the image isn't displayed correctly, select the desired video format manually. Use to select the language used in the menus. ( / English / Español / Deutsch / Français / Italiano / ) RESET ALL . . . . . . . . Use to reset the MENU settings (except LANGUAGE). Use to adjust the horizontal position of the image. Use to adjust the vertical position of the image. Use to avoid image noise such as wide stripes. Use to synchronize the projector with PC input signals so that the image is not blurred. This will be set automatically to match the input signal to component video (YCBCR/YPBPR) or RGB. Select ON when playing DVD discs containing data of widescreen images. Adjusts the image when flagging occurs near the top of the screen. opt. XGA60 SIGNAL HORIZ. POSITION VERT. POSITION TRACKING FINE SYNC RGB RGB 0 0 0 0 RGB OFF ON OK COMPUTER INPUT ANAMORPHIC HOLD USER 5 SIGNAL - USER (Normally, there is no need for adjustments. ) CLAMP POSITION/ CLAMP WIDTH . . . . . . . . . If you use something similar, the brighter colors of the projected image may become blurred. [. . . ] · · The first character of the Status code from projector may not be displayed correctly. In this case, reject the first character on the computer side. * : The sending time of return command may delay depending on the condition (during changing the input signal, etc. ). [Example] Turn the power ON (' 'is for ASCII code) Sending commands from the PC etc. 30 30 21 0D '0' '0' '!' ' ' 30 30 21 0D '0' '0' '!' ' ' Status code from projector Meaning Command for POWER ON Command received (Command echo back) 4) Operation commands The operation commands execute the basic operation setting of this projector. [. . . ]