User manual MITSUBISHI XD2000U

[. . . ] DLPTM PROJECTOR MODEL XD2000U XD1000U User Manual XD2000 XD1000 This User Manual is important to you. Please read it before using your projector. ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. WARNING Use the attached specified power supply cord. If you use another power-supply cord, it may cause interference with radio and television reception. [. . . ] The operating sound is reduced and the lamp lifetime becomes longer. · When the lamp mode is switched, the projected image may flicker. · Frequent switching of the lamp mode may damage the lamp. When ON is chosen, the lamp is automatically lit when the power cord is plugged in the wall outlet. Choose ON when using the projector mounted on the ceiling. · The projector is in the stand-by mode when the lamp is off. Use the remote control to turn on the lamp. Use to set the time elapsed before the projector enters the stand-by mode when there is no signal input from the source. Choose ON to display the splash screen when the power is turned on. Use to change the color of the screen that appears when no signal is supplied. Select when viewing images from the front with the projector installed on the floor. Select when viewing images projected from the behind of the screen with the projector installed on the floor. Select when viewing images projected from the behind of the screen with the projector installed on the ceiling. Select when viewing images from the front with the projector installed on the ceiling. Use to show the test pattern of the crossing hatch. Use to enable or cancel the FOCUS LOCK and ZOOM LOCK. Use to enable or cancel the LENS SHIFT LOCK. Use to reset the position of the lens to the factory setting. 2. INSTALLATION menu ITEM SETTING LAMP MODE STANDARD LOW AUTO POWER ON ON / OFF AUTO POWER OFF SPLASH SCREEN BACK COLOR IMAGE REVERSE OFF / 5 - 60min ON / OFF BLUE / BLACK OFF MIRROR INVERT MIRROR INVERT TEST PATTERN CROSS HATCH ZOOM/FOCUS LOCK ON / OFF LENS SHIFT LOCK ON / OFF LENS SHIFT RESET OK · · Regardless of the setting of LAMP MODE in the INSTALLATION menu, the STANDARD lamp mode is activated by default whenever the projector is turned on. When LAMP MODE has been set to LOW, the lamp mode changes from STANDARD to LOW about 1 minute after turn-on. To cancel the test pattern, press any button. EN-23 ENGLISH Menu operation (continued) 3. FEATURE menu ITEM SETTING ASPECT AUTO FUNCTION Select to change the aspect ratio automatically depending on the input signal. [. . . ] Video signals having resolution exceeding the maximum resolution supported by this projector are reduced to the maximum resolution size of the projector even in the REAL mode. This projector doesn't support 480i, 576i, and 480p signals from video devices having 5 lines (R, G, B, H, V). EN-39 ENGLISH Specifications (continued) Connectors SERIAL (D-SUB 9-pin) 5 9 1 10 6 15 Pin No. 1 2 3 4 5 6 7 8 9 Name TXD RXD GND I/O IN OUT - COMPUTER IN / COMPONENT VIDEO IN (Mini D-SUB 15-pin) 5 1 Pin No. R(RED)/CR G(GREEN)/Y B(BLUE)/CB GND GND GND GND GND DDC 5V GND GND DDC Data HD/CS VD DDC Clock DVI-D (HDCP) (DVI-D 24-pin) 16 24 17 9 6 11 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 8 1 PIN No. [. . . ]